P8T-0R5G18G-60-T-SFF-BR is a high speed, single pole, eight throw, absorptive switch capable of switching within 100 ns.

BPF-3D25G-87D1M-SFF is a bandpass filter centered at 3.25 GHz with a 3.20645 to 3.29355 GHz passband and a maximum insertion loss of 1.1 dB.

PS-200M4G-12B-SFF is a 12-bit digital phase shifter that operates over the 0.2 to 4 GHz frequency range. 

PIQ-1-SMT is an integrated broadband IQ Vector Modulator with fully differential inputs and outputs (LO and RF) ports and single-ended on the baseband (I and Q) inputs. 

Planar Monolithics (PMI) Model ISO-26-18-SMF is a 2 to 6 GHz coaxial isolator with an insertion loss of 0.8 to 1.5 dB maximum.

PIQ-1-SMT-EVAL is an evaluation board for PIQ-1-SMT that is an integrated broadband IQ vector modulator with fully differential inputs and outputs (LO and RF) ports and single-ended on the baseband (I and Q) inputs. 

PA-218-45-5-10W-24V-SFF is a 2 to 18 GHz solid state power amplifier (SSPA) featuring 38 to 48 dB gain.

Planar Monolithics (PMI) Model PS-500M2G-10B-SFF-MIL-SM is a 0.5 to 2 GHz, digitally controlled, 0 º to 360º phase shifter. 

PEAFS3-14-0R2535R0-6R5-23-12-292MF is an 8 to 18 GHz low noise amplifier that provides over 13 dB gain with a gain flatness of ±1 dB maximum.

Planar Monolithics (PMI) Model PLO-48D4G-EXT is an externally referenced phase-locked dielectric resonator oscillator covering the frequency of 48.4 GHz with a load VSWR: 1.5:1.

LM-118-100W-22DBM is an RF Limiter that operates in the range of frequencies from 1 to 18 GHz that can handle up to 100 W CW over temperature (-55 to +85 °C). 

P1T-500M18G-80-R-SFF-SW21841A-515 is a reflective, high speed, single pole single throw switch operating over the frequency range of 0.5 to 18 GHz.

PS-100M20G-10B-SFF-MIL-SM is a 0.1 to 20 GHz digitally controlled phase shifter with capability for phase shifting from 0º to 360º with an insertion loss of 13 dB.

PEC-42-1G40G-20-12-292FF is a 1 to 40 GHz, Ultra-Wideband Low Noise Amplifier that provides 42 dB of gain and gain flatness of  ±2.5 dB

8SFB-2G18G-SFF is a Switch Filter Bank with a frequency range of 2 to 18 GHz and has an insertion loss of 8 dB typical.

DTA-200M18G-100-CD-EXT is an 8 Bit Digitally Tuned Attenuator designed for the 0.2 to 18 GHz frequency range and offering an attenuation range of 100 dB. 

P1T-DC18-60-T-SFF-HSLVT is a single pole, single throw, absorptive switch that offers ultra-low video transient performance while providing ultra-fast switching speed of 6 ns.

PS-100M20G-10B-SFF-MIL-SM is a 0.1 to 20 GHz, 10 Bit digital phase with 0º to 360º phase shift offering an insertion loss of 13 dB; amplitude error of ±1 dB; phase shift error ±5°; switching speed of 500 ns and spurious of -60 dBc.

Model P2T-0R3G18G-80-T-55-SFF is a single pole, double throw, absorptive switch that operates from 0.3 to 18 GHz that offers a low insertion loss of 3.5 dB.

Model PE2-15-5R06R0-3R5-21-12-SFF is a 5 to 6 GHz Low Noise Amplifier designed for military and industrial applications. That provides 15 dB of gain and 19 dBm P1dB while maintaining a maximum gain flatness of ±0.5 dB.

Model MA-6G11G-20DB-SFF is a 6 to 11 GHz Mechanical Variable Attenuator that offers an attenuation range of 0 to 10 dB and attenuation flatness of ±0.5 dB.

Model HP3G55M18G-SMA is a high pass filter that has a frequency range of 3.55 to 18 GHz with a cut-off frequency of 3.14 GHz.

Model PLO-48D4G-EXT is an externally referenced Phase Locked Dielectric Resonator Oscillator (PLDRO) covering the frequency of 48.4 GHz with a load VSWR: 1.5:1.

Model P8T-0D418-75-T-SFF-NG is a single pole, eight throw, absorptive switch that operates over the frequency range of 0.4 to 18 GHz with a minimum isolation of 75 dB .

Model LM-10M2D5G-100CW-1KWP-SFF is a RF limiter that operates in the 0.01 to 2.5 GHz frequency range. This limiter can handle 100 W CW and 1 kW peak (1% duty cycle, with 1 µs maximum pulse width) input power.

Model MA-1D5G2G-15DB-SFF is a 1.5 to 2 GHz Mechanical Variable Attenuator that offers an attenuation range of 0 to 15 dB; attenuation flatness of ±0.5 dB; insertion loss of 0.5 dB and VSWR of 1.7:1.  

Model HP-55G57G-185FF is a high pass filter having a passband of 55 to 57 GHz. Cut-Off Frequency is 50 GHz with a maximum passband insertion loss of 2 dB.

Model PE2-17-218-20-12-SFF is a 2 to 18 GHz low noise amplifier with a gain of 17 dB; 4.5 dB noise figure; gain flatness is ±1.75 dB; and a OP1dB of 20 dBm. 

Model P4T-500M18G-80-T-SFF-IND-1 is a SP4T, Absorptive PIN Diode Switch that operates over 0.5 to 18 GHz frequency range that offers 80 dB of isolation,  insertion Loss is 3.75 dB Max.

Quantic PMI Model BPF-35D-4G-292FF is a bandpass filter with a bandpass of 33 to 37 GHz that provides 60 dBc of rejection @ DC to 31 GHz & 39 to 43 GHz with a typical insertion loss of 2 dB.

Quantic PMI Model DTA-2G18G-60-12-CD-1-20DBM-TS-NSI is a 12 BIT Programmable 60 dB Pin Diode Attenuator over the frequency range of 2 to 18 GHz that offers an attenuation range of 60 dB with a minimum step size of 0.016 dB.

Quantic PMI Model P2T-500M18G-60-R-1W-SFF is a single pole, two throw, reflective switch operating over the frequency range of 0.5 to 18 GHz with a minimum isolation of 60 dB.

Quantic PMI Model LM-20M18G-100W-15DBM-NFM is an High Power limiter that operates in the frequency range of 0.02 to 18 GHz that can handle 100 W CW for all temperatures (-55 to +85 °C) and 1 kW peak (1% duty cycle.

Quantic PMI Model P1T-DC18-60-T-SFF-HSLVT is a single pole, single throw, absorptive switch which offers ultra-low video transient performance while providing ultra-fast switching speed of 6 ns;.

PLN-25-812-10-LCA is an 8 to 12 GHz Low Noise Amplifier that provides 25 dB of gain while maintaining a gain flatness of ±1 dB. 

Quantic PMI Model P3T-250M40G-60-T-55-292FF is a high speed, single pole, three throw, absorptive switch capable of switching within 50 ns.

Quantic PMI Model LM-10M18G-16-20W-AL-ROHS is a coaxial limiter with an operating range of 0.1 to 18 GHz.

Quantic PMI Model PMC-600M3G500M-SFF is a monopulse comparator operating over the 0.6 to 3.5 GHz frequency range with a maximum 6.5 dB insertion loss .

Quantic PMI Model HP3G55M18G-SMA is a high pass filter that operates over the frequency range of 3.55 to 18 GHz. 

Quantic PMI Model PE2-618-25-4D5-27-SFF is a Low Noise Amplifier designed for military and industrial applications. This amplifier operates over the 6 to 18 GHz with a gain of 26 dB.

Quantic PMI Model PE2-34-2G18G-3R5-15-SFF-VVG-DD is a voltage variable gain amplifier with integrated diode detector operating over the frequency range of 2 to 18 GHz.

P5T-218-80-T-25DBM-SFF is a single pole, five throw absorptive switch designed to operate over the 2 to 18 GHz frequency range that is designed to maintain low insertion loss of 3.2 dB.

PA-218-45-5-2W-24V-SFF is a 2 to 18 GHz power amplifier with 45 dB typical gain, a noise figure of 5 dB maximum and a saturated output power of 2 W minimum. 

PS-30M2G-8B-SFF is a 0.03 to 2 GHz digitally controlled analog phase shifter with capability for phase shifting from 0° to 360°. 

PS-360-2433D5-6-SFF-1 is a 2.433 ± 0.001 GHz, 6-BIT digitally controlled phase shifter that offers up to 360° of phase shift range with a phase accuracy of ±8° typical. 

DLVA-70M-80-15V is a Successive Detection Log Video Amplifier designed to operate over the 0.05 to 0.09 GHz frequency range. 

PIQ-2G18G-360-16-CD-2 is a 2 to 18 GHz, high performance I/Q Vector Modulator with 2 x 12-bit monotonic TTL compatible channels (I and Q). 

PFS-1G20G is a frequency synthesizer that operates over the 1 to 20 GHz frequency range using RS232 input controls and a 10 MHz reference signal. 

SATCOM-0001 is an ultra-small band reject filter centered at 0.255 GHz that has a stopband frequency range of 0.24 to 0.27 GHz.

SBA-100M18G-31D5-6B-RL-SFF is a switched bit attenuator operating from 0.1 to 18 GHz designed to be switched between a low insertion loss state and 31.5 dB in 0.5 dB steps. 

PE2-30-8R018R0-3R5-22-12-SFF is an 8 to 18 GHz, Low Noise Amplifier with a typical gain of 30 dB while maintaining a maximum gain flatness of ±1.5 dB over the operating frequency. 

P1T-1G18G-65-T-SFF is an Absorptive, High Speed, Single Pole Single Throw Switch capable of switching within 50 ns maximum over the frequency range of 1 to 18 GHz with a 65 dB isolation. 

PS-360-16G22G-10B-SFF is a 16 to 22 GHz, digital controlled phase shifter with capability for phase shifting from 0º to 360º with 10-Bit accuracy. 

Quantic PMI’s solid-state digital and analog controlled attenuators are designed for commercial, industrial and military applications including transmission loss simulation, signal fading/handover system evaluation and telecom network infrastructure.

PE2-25-200M18-3D5-25-SFF is a 0.2 to 18 GHz Low Noise Amplifier that provides >23 dB of gain while maintaining a maximum gain flatness of ±2 dB maximum over the operating frequency. 

PA-30-1D32D7-SFF is a power amplifier that operates over the frequency range of 1.3 to 2.7 GHz that offers a minimum small signal gain of 30 dB.

P1T-DC52G-65-T-24FM is an absorptive, single pole, single throw pin diode switch that operates from DC to 52 GHz that has an isolation of 60 dB @ 52 GHz.

SATCOM-0001 is an ultra-small band reject filter centered at 0.255 GHz that has a stopband frequency range of 0.24 to 0.27 GHz.

DTA-100M40G-15DB-10BIT Is a 10-bit programmable 16 dB attenuator with step resolution of 0.015625 dB over the frequency range of 0.1 to 40 GHz.

LM-10M12G-20-10W-SFF is a high-power limiter operating in the frequency range of 0.01 to 12 GHz.

P1T-DC40G-65-T-292FF-1NS-OPT10M20G is an absorptive, single pole single throw FET Switch that operates from 0.01 to 20 GHz with a typical 6 ns switching speed.

JTIDS-0001-SFM-ROHS is an ultra-small band reject filter centered at 1.085 GHz. This filter rejects frequencies from 0.96 to 1.21 GHz.

PEAFS3-14-0R2535R0-6R5-23-12-292MF is an 8 to 18 GHz low noise amplifier that provides over 13 dB gain with a gain flatness of ±1 dB maximum.

TD-30T-SHS-218-30DBAMP-OPT100M4G is an ultra-high-speed, high sensitivity threshold detector designed for broadband applications in the 0.1 to 4 GHz frequency range.

DTA-200M18G-60-CD-EXT is a 10-Bit Digital Attenuator designed for the 0.2 to 18 GHz frequency range using an external latch to set the attenuation.

PA-46-0D5-SFF is a power amplifier that operates over the frequency range of 0.5 to 3 GHz with a typical small signal gain of 46 dB.

Quantic PMI Model No. DTA-0R5G4G-60-CD-1-OPT12VDC is a non-reflective 10-Bit Programmable 60 dB Pin Diode Attenuator with step resolution as low as 0.06 dB over the frequency range of 0.5 to 4 GHz. 

Quantic PMI Model P6T-2G20G-55-T-SFF is an absorptive, single pole, six throw pin diode switch that operates over the 2 to 20 GHz frequency range and has a minimum isolation of 55 dB

Quantic PMI Model LM-118-100W-22DBM is an RF Limiter that operates in the range of frequencies from 1 to 18 GHz that can handle up to 100 W CW over temperature (-55 to +85 °C). 

Quantic PMI Model PEC-42-1G40G-20-12-292FF-BT is a 1 to 40 GHz Low Noise Amplifier that has a typical gain of 40 dB while maintaining a ±2.5 dB flatness with a Psat of 20 dBm @ 40 GHz.

Quantic PMI Model SDLVA-1G20G-55-12-SFF is a miniature Successive Detection Log Video Amplifier (SDLVA) that operates from 1 to 20 GHz with logging range of -55 to +5 dBm.

Quantic PMI Model EQL-26D5G40G-1D5DB-292MF is a 26.5 to 40 GHz, Passive Amplitude Equalizer with a negative slope.  

Quantic PMI Model PS-30M2G-8B-SFF is a 0.03 to 2 GHz digitally controlled analog phase shifter with capability for phase shifting from 0° to 360°. 

Quantic PMI Model PIQ-2G18G-360-16-CD-2 is a 2 to 18 GHz, high performance I/Q vector modulator with 2 x 12-bit monotonic TTL compatible channels (I and Q).

Quantic PMI Model LM-1D2G1D4G-4KW-20DBM-SFM is a limiter with an operating range of 1.2 to 1.4 GHz. 

Quantic PMI Model PMSN-4DT-561R875-NG-H02 is a terminated single pole four throw integrated switch module, which includes high speed SP4T, pin diode limiter, video filter, gain equalizer, attenuator, and amplifier. 

Quantic PMI Model DTA-2G18G-60-12-CD-1-20DBM-TS-NSI is a 12-bit programmable 60 dB pin diode attenuator over the frequency range of 2 to 18 GHz.

Quantic PMI Model PA-218-45-5-4W-SF is a 2 to 18 GHz power amplifier with 45 dB typical gain, a noise figure of 5 dB maximum and a saturated output power of 4 W minimum. 

Quantic PMI Model P1T-DC40G-65-T-292FF-1NS-OPT10M20G is an absorptive, single pole single throw FET Switch that operates from 0.01 to 20 GHz with a typical 6 ns switching speed.

PS-360-DC-3 OPTION 618-15D-10BIT is a 10-Bit, digitally controlled phase shifter operating over the 6 to 18 GHz frequency range. This high speed phase shifter has a range of 360 degrees.

PA-218-45-5-2W-24V-SFF is a 2 to 18 GHz power amplifier with 45 dB typical gain, a noise figure of 5 dB maximum and a saturated output power of 2 W minimum. 

CL6250-830-CD-SFF is a combline bandpass filter with a center frequency of 6.25 GHz with a bandwidth of 0.83 GHz and rejection of 60 dB Min from DC to 3.8 GHz & 8 to 12 GHz. 

Quantic PMI Model LM-1G18G-15-25W-SFF is a high power limiter that operates over the 1 to 18 GHz frequency range. 

DTA-2G18G-60-12-CD-1-20DBM is a non-reflective, 12 bit, programmable 60 dB pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 2 to 18 GHz.

 P2T-218-60-512-R-SFF is a single pole, two throw, reflective switch operating over the frequency range of 2 to 18 GHz with a minimum isolation of 60 dB and a maximum insertion loss of 1.8 dB. 

SDLVA-18G40G-CD-1 is a Successive Detection Logarithmic Video Amplifier (SDLVA) designed to operate over the 18 to 40 GHz frequency range with a dynamic range of -70 to +5 dBm.

P6T-2G18G-55-R-512-SFF-ROHS is a high speed, single pole, six throw, reflective switch capable of switching within 15 ns. The frequency range is 2 to 18 GHz.

PA-2040-22G-8W-18V-292FF is a high-power amplifier with an operating frequency range of 20 to 40 GHz that offers 22 dB of gain and a saturated output power of 8 W. 

P2T-1840-60-R-1W-292FF is a reflective single pole, two throw switch that operates from 18 to 40 GHz which handles 1 W CW power. 

PTP-3D2G-5D625G-9D5G-SFF is a high rejection triplexer with center frequencies of CH 1: 3.2 GHz, CH 2: 5.625 GHz and CH 3: 9.5 GHz.

PLDRO-17D45G-25M-EXT-ROHS is a PLDRO with an output frequency of 17.45 GHz. It has a reference frequency of 25 MHz and an output power of 13.8 dBm.

PLNA-4G8G-42-4D5DB-10BBM-SFF is a Low Noise Amplifier that operates over the 4 to 8 GHz frequency range. Designed for military and industrial applications.

ERDLVA-2G18G-65-70MV-70C is a CW Immune ERDLVA that operates from 2 to 18 GHz; VSWR of 2.2:1; input power of 1 W; TSS of -71 dBm, and dynamic range of -65 to 0 dBm.

PS-360-DC-3 OPTION 618-15D-10BIT is a 10-Bit, digitally controlled Phase Shifter operating over the 6 to 18 GHz frequency range. This high-speed phase shifter has a range of 360°.

PE2-16-300M20G-1R7-15-12-SFF is a low noise amplifier (LNA) that works from 0.3 to 20 GHz. This amplifier has an extremely low noise figure over this broad frequency range. 

SDLVA-1G20G-55-12-SFF-100MV is a miniature Successive Detection Log Video Amplifier supplied in our standard PE2 housing that can be used in connectorized or strip line applications.

LM-12-20-5W-2 is an RF power limiter with a frequency range of 1 to 2 GHz, average power of 5 W, and peak power of 400 W.

P20T-4G8G-80-T-515-SFF-HERM is an Absorptive, SP20T, Pin Diode Switch that operates over the 4 to 8 GHz frequency range with a switching speed of 2 µs Max.

PEC-30-10M20-SFF-ROHS is an exceptionally low noise amplifier with a working frequency range of 0.01 to 20 GHz. 

FD-70M-50M-1212-50OHMS is a Frequency Discriminator that operates at a center frequency of 70 MHz. It has a peak bandwidth of 90 MHz and a linear bandwidth of 50 MHz minimum.

DTA-18G40G-60-CD-1 is a 11 Bit programmable 60 dB digital attenuator with step resolution as low as 0.05 dB over the frequency range of 18 to 40 GHz.

LM-1G18G-15-10W-500WP-SFF is a high power limiter that operates over the 1 to 18 GHz frequency range that can handle an input power of 10 W CW and 500 W Max (@ 0.1% Duty Cycle.

11DP-11R5/16R5-CD-SFF is a diplexer that offers passbands at 10.75 to 12.25 GHz and 15.75 to 17.25 GHz.  The passband insertion loss is less than 3 dB and the VSWR is 1.5:1 Max.  

HP-120-CD-SFF is a broadband high pass filter having a passband of 1 to 20 GHz. Cut-Off Frequency is 1 GHz with a maximum passband insertion loss of 2.0 dB from 1 to 20 GHz. 

DTA-100M40G-30-CD-1 is a 5-Bit programmable 30 dB PIN diode attenuator with a step resolution of 1.0 dB over the frequency range of 100 MHz to 40 GHz. This model operates on a single +12 to +15 VDC supply and draws only 40 mA of current.

P6T-2G18G-55-R-512-SFF-ROHS is a high speed, single pole, six throw, reflective switch capable of switching within 15 ns. The frequency range is 2 to 18 GHz and has over 55 dB of isolation. 

PE2-16-300M20G-1R7-15-12-SFF is a low noise amplifier that works from 0.3 to 20 GHz. he P1dB output power of 15 dBm allows this low noise amplifier to function as a lo driver for balanced, I/Q or image reject. 

Quantic PMI Model PMC-2D22D4-6D8-SFF is a monopulse comparator that operates over the frequency range of 2.2 to 2.4 GHz with a maximum insertion loss of 6.8 dB.

BPF-3R55G-500M-SFF is a bandpass filter with a center frequency of 3.55 GHz with a bandwidth of 0.5 GHz

 PEC-40-25-218-21-12-SFF-TTLVG is a variable gain amplifier that operates over the 2.0 to 18.0 GHz frequency range. This model has two gain states.

PS-360-16G22G-10B-SFF is a 16 to 22 GHz, digital controlled phase shifter with capability for phase shifting from 0º to 360º with 10-Bit accuracy. 

Quantic PMI Model ISO-618-10-SFF is a 6 to 18 GHz coaxial isolator with an insertion loss of 1.5 dB maximum.

P8T-2G18G-60-T-SFF-NSI is a single pole, eight throw, absorptive switch module with low loss, high speed and with integral TTL driver, designed for broadband operations 2 to 18 GHz. 

Quantic PMI Model HP0R5G-18G-CD-SFF-ROHS is a broadband high pass filter having a passband of 0.5 to 18 GHz. Cut-Off Frequency is 0.5 GHz with a passband insertion loss of 2.0 dB from 1 to 16 GHz. 

Quantic PMI Model BPF-1D3G2D3G-SMT is a Bandpass Filter that operates in the 1.3 to 2.3 GHz frequency range with a maximum passband insertion loss of 5 dB.

Quantic PMI Model PMI-AFD4-020080-23P-SMA-2 is a 2 to 8 GHz amplifier that provides a maximum gain of 35 dB with a maximum gain flatness of ±2.0 dB.

Quantic PMI Model P16T-100M27G-100-T-DEC is a single pole 16 throw solid state absorptive switch operating over the 100 MHz to 27 GHz frequency range.

Quantic PMI Model LM-10M40G-15DBM-4W-AGAL is a Limiter with a frequency range of 0.01 to 40 GHz. 

Quantic PMI Model PDVAN-8018-60-8-OPT25DBM is an 8-Bit digital programmable attenuator that operates over the frequency range of 8 to 18 GHz. 

Quantic PMI Model SDLVA-2G18G-50MV-100-NRF is a successive detection logarithmic amplifier (SDLVA) designed to operate over the 2 to 18 GHz frequency range with a frequency flatness of 1.64 dB.

Quantic PMI Model 5CL9D18G-180-CD-SFF is a bandpass filter centered at 9.18 GHz with a nominal bandwidth of 0.18 GHz.

Quantic PMI Model ERDLVA-18G40G-65-50-1 is a CW Immune Extended Range Detector Log Video Amplifier (ERDLVA) that operates from 18 to 40 GHz with a dynamic range of -65 to 0 dBm.

Quantic PMI Model LM-10M18G-16-20W-AL-OPT418 is a coaxial limiter with an operating range of 4 to 18 GHz. This model has a maximum insertion loss of 2.5 dB at -10 dBm input power.

Quantic PMI Model PEC-30-10M20-SFF is an exceptionally ultra-low noise amplifier with a working frequency range of 0.01 to 20 GHz.  

Quantic PMI Model PS-90-6012-HS15NS is a Miniature High-speed Bi-Phase Modulator / Phase Shifter that operates in the 6 to 12 GHz frequency range, 0 & 180° phase states and insertion loss of 2.5 dB typical

Quantic PMI Model SDLVA-1G20G-58-12-SFF is a 1 to 20 GHz Successive Detection Log Video Amplifier (SDLVA).  Excellent performance is packed into this ultra-small package. 

Quantic PMI Model P2T-12G18G-45-R-SFF-10W is an independently controlled, high power, reflective single pole two throw switch designed to operate between 12.0 to 18.0 GHz .

Quantic PMI Model ERDLVA-18G40G-65-50-1 is a CW Immune Extended Range Detector Log Video Amplifier (ERDLVA) that operates from 18 to 40 GHz with a dynamic range of -65 to 0 dBm.

Quantic PMI Model DTA-0R5G18G-60-CD-4 is a non-reflective, 10 bit, programmable 60 dB pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 0.5 to 18 GHz.

Quantic PMI Model PEC-54-8G18G-14DBM-SFF is a limiting amplifier with an operating frequency range of 8 to 18 GHz that offers a gain range of +50 to +58 dB with a gain flatness of ±3.5 dB maximum, a noise figure of 7.5 dB.  

Quantic PMI Model PUB-15-30M20G-20-LCA is a 0.03 to 20 GHz Low Noise Amplifier which provides 15 dB of gain while maintaining a gain flatness of ±2.5 dB typically over the operating frequency. 

Quantic PMI Model GMDA-D1004 is an Extended Dynamic Range DLVA designed to operate over the 2 to 18 GHz frequency range. 

Quantic PMI Model LM-0518-10-1W-SHS-2-FM is a High-Power Limiter that operates from 0.5 to 18 GHz.  This limiter handles 100 W Peak Power with a pulse width of 1 µs. 

Quantic PMI Model P1T-18G40G-90-1515-292FF-ROHS is an absorptive, high speed, single pole, single throw switch capable of switching within 15 to 25 ns. 

Quantic PMI Model BPF-3D96G-65M-SFF is a bandpass filter with a center frequency of 3.96 GHz and has a max insertion loss of 1.4 dB and a maximum VSWR of 1.4:1.

Quantic PMI Model DTA-2G18G-60-12-CD-1-20DBM-TS-NSI is a 12-Bit Programmable 60 dB Pin Diode Attenuator over the frequency range of 2 to 18 GHz. 

Quantic PMI Model PE2-15-30M26R5-5R5-18-12-SFF is a 0.03 to 26.5 GHz Low Noise Amplifier which provides a typical gain of 15 dB while maintaining a maximum gain flatness of ±2.0 dB. 

Quantic PMI Model No. PS-85M4G-9B-SFF is a 0.085 to 4.0 GHz, Digitally Controlled Phase Shifter with capability for phase shifting from 0° to 360°. 

Quantic PMI Model LM-1G18G-2W-SFF-BIAS is a low loss limiter with a P1dB bias adjust and working frequency range of 1 to 18 GHz. 

Quantic PMI Model No. P2T-3040-60-R-292FF-RC is a single pole, two throw pin diode switch that operates over the 30 to 40 GHz frequency range. 

LM-10M2D5G-100CW-1KWP-SFF-ROHS is a RF limiter that operates in the 0.01 to 2.5 GHz frequency range. This limiter can handle 100 W CW and 1 kW peak (1% duty cycle, 1 µs maximum pulse width) input power.

PS-360-16G22G-10B-SFF is a 16 to 22 GHz, digital controlled phase shifter with capability for phase shifting from 0º to 360º with 10-Bit accuracy. 

PCG-12-0DBM-12V-SFF is a 1 to 2 GHz RF input, 1 to 26 GHz output comb generator. The small size active unit allows input power of only 0 to +5 dBm and is powered with +12 V. 

ERDLVA-218-CW-75MV-93 is a CW immune extended range detector log video amplifier (ERDLVA) that operates between the 2 to 18 GHz frequency range with a log slope of 75 mV/dB and rise time of 25 ns.

P8T-2G18G-60-T-SFF-NSI is a single pole, eight throw, absorptive switch module with low loss, high speed and with integral TTL driver, designed for broadband operations 2 to 18 GHz. 

Quantic PMI Model HP8G-7D8G-CD-SMF is a High Pass Filter with a Passband of 8 to 22 GHz. The Compact 1.15" x 0.70" x 0.50" housing is outfitted with SMA Connectors. 

LM-1G18G-2W-SFF-BIAS is a low loss limiter with a P1dB bias adjust and working frequency range of 1 to 18 GHz.  

PEC-30-0R5G50G-22-12-24FF is an Ultra-Broadband Low Noise Amplifier that operates over the 0.5 to 50 GHz, provides a typical gain of 30 dB while maintaining a ±2.5 dB flatness with a noise figure of 9 dB maximum.

EQL-DC40-20-292FF is a DC to 40 GHz passive equalizer with a 20 dB Typ loss at 10 MHz with a insertion loss of 3 dB Typ at 40 GHz. 

PLDRO-13D95G-25M-EXT-ROHS is a PLDRO with an output frequency of 13.950 GHz and a reference frequency of 25 MHz, and an output power of +13 to +15 dBm, a VSWR of 3:1.

P8T-10G31G-70-T-55-292FF-ROHS is a high speed, single pole, eight throw (SP8T), absorptive switch capable of switching within 50 ns. 

LM-150M5G-200CW-2KWPK-AGAL-ROHS is a ultra-high power limiter operating in the frequency range 150 MHz to 5 GHz, with 200 W CW power handling (+53 dBm).

P5T-218-60-R-25DBM-SFF is a single pole, five throw reflective switch designed to operate over the 2 to 18 GHz frequency range. 

Quantic PMI Model No. PE2-30-20G20R6G-3R0-10-12-SFF is a 20.0 to 26.5 GHz, Low Noise Amplifier. This amplifier offers a gain of +30 dB typical with a gain Flatness of ±1.5 dB maximum.

Quantic PMI Model P1T-DC40G-65-T-292FF-1NS-OPT18G-50OHM is a SPST Absorptive, FET switch that operates from DC to 18.0 GHz. 

Quantic PMI Model LM-2G18G-RAD-3W-19DBM-SMF is a low leakage limiter operating over the 2 to 18 GHz frequency range. This model offers excellent temperature stability with exceptionally low loss of 2.5 dB.

Quantic PMI Model ERDLVA-2G18G-65-70MV-85C is a CW Immune ERDLVA that operates from 2.0 to 18.0 GHz with a Video Out TSS of -71 dBm; Video Out Dynamic Range of -65 to 0 dBm and more.

Quantic PMI Model 8CL1800-100-CD-SFF is a bandpass filter centered at 1.8 GHz. The nominal bandwidth is 0.1 GHz; VSWR of 1.5:1; insertion loss of 1.5 dB; and rejection of -60 dBc @ 1.64 and 2.0 GHz. 

Quantic PMI Model P4T-100M18G-80-T-515-SFF-4W-IND is a Single Pole, Four Throw Absorptive Switch operating from 0.1 to 18.0 GHz. It offers 80 dB minimum of isolation with a maximum insertion loss of 6.0 dB.

DTA-0R4G18G-60-CD-1 is a non-reflective, 10-bit, programmable 60 dB pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 0.4 to 18.0 GHz. 

TD-30T-SHS-218 is a high speed, TTL logic output threshold detector designed to operate from 2 to 18 GHz with a propagation delay of 15 ns maximum; dynamic range up to +10 dBm.

LM-0118-10-1W-SHS-2-FM is a high-power limiter that operates from 100 MHz to 18 GHz that handles 100 W peak power with a pulse width of 1 µs.

 P1T-DC40G-65-T-292FF-1NS-OPT18G is a SPST Absorptive, FET switch that operates from DC to 18.0 GHz. 

PE2-35-120-5R0-10-12-SFF is a 1.0 to 20.0 GHz, low noise amplifier that typically provides 35 dB of gain while maintaining a maximum gain flatness of ±1.5 dB over the operating frequency. 

PS-5G18G-400-A-SFF is a 5 to 18 GHz, Low Phase Noise, Analog Phase Shifter with Capability for Phase Shifting from 0 to 400°. 

PS-90-6012-HS15NS-OPT6D1G is a high speed 6.1 GHz, 0 to 180°, Miniature Bi-Phase Modulator / Phase Shifter with TTL control logic.  

SDLVA-18G40G-65-CD-292FF is a Successive Detection Log Video Amplifier (SDLVA) that operates between the 18.0 to 40.0 GHz frequency range.

PEC-30-10M20-SFF is an exceptionally low noise amplifier with a working frequency range of 10 MHz to 20 GHz.  

The PEC-42-500M40G-20-12-292MM is a 500 MHz to 40 GHz Ultra-Wideband Low Noise Amplifier that provides typically 42 dB of gain with a noise figure of 5.5 dB at 20 GHz. 

The P16T-18G40G-90-T-512-SFF-DEC is a Single Pole, Sixteen Throw, Absorptive Switch with a frequency range of 18.0 to 40.0 GHz.

The SBA-500M18G-31D5-6B-SFF is a switched bit attenuator operating from 0.5 to 18 GHz designed to be switched between a low insertion loss state and 31.5 dB in 0.5 dB steps. 

DLVA-8G10G-75-50-SFF is a DLVA with a frequency range of 8.0 to 10.0 GHz. This model offers a flatness of 1.1 dB, a TSS of -78 dBm and a log dynamic range of -75 to 0 dBm

P1T-200M18G-80-T-SFF-RL is a high speed, single pole, single throw, absorptive switch capable of switching within 30 ns. The frequency range is 0.2 to 18.0 GHz.

EQL-DC20-10-SFF is a DC to 20 GHz passive equalizer with a nominal slope of 9 dB, 10 dB typical loss at DC with an insertion loss of 1 dB typical at 20 GHz.  

6SFB-30M600M-CD-SFF is a 6-Channel Switched Filter Bank with a frequency range of 30 to 600 MHz and has an insertion loss of 4.5 dB, a VSWR of 1.3:1 and a minimum isolation of 40 dB.

HP3G55M18G-SMA is a high pass filter that operates over the frequency range of 3.55 to 18.0 GHz with a maximum insertion loss of 1.5 dB and a maximum VSWR of 2.0:1. 

HADA-D2002 is a Detector Log Video Amplifier (DLVA) that operates between the frequency range of 2.0 to 18.0 GHz. It has a dynamic range of 40 dB with a log slope of 50 mV/dB and a nominal video bandwidth of 12 MHz. 

PEC-30-500M40G-20-12-292FF is a 500 MHz to 40 GHz Low Noise Amplifier. This amplifier has a typical gain of 30 dB with ±2.5 dB flatness; a noise figure of 5.5 dB.

PEAFS3-14-0R2535R0-6R5-23-12-292FF is a 0.25 to 35 GHz low noise amplifier with a gain of 14 dB and a gain flatness of 1.5 dB.

DTA-2G18G-64-10B-SFF is a 10-Bit Programmable Attenuator with a frequency range of 2.0 to 18.0 GHz. 

LM-10M37G-15DBM-10W-AGAL is a Limiter that operates over the 10 MHz to 37.0 GHz frequency range.

PMI-AFD4-020080-23P-SMA-2 is a 2.0 to 8.0 GHz amplifier that provides a maximum gain of 35 dB with a maximum gain flatness of ±2.0 dB.

Quantic PMI Model No. P1T-DC18-60-T-SFF-HSLVT is a single pole, single throw, absorptive switch which offers ultra-low video transient performance while providing ultra-fast switching speed of 6 ns.

PDRO-7519R95M-13DBM-SFF-ROHS is a Phase Locked Oscillator (PLO) with an output frequency of 7519.95 MHz and a minimum output level of +13 dBm.  

LM-4G18G-100W-15DBM-SMF is a high-power limiter that operates over the 4.0 to 18.0 GHz frequency range. Specifications include an input power of +50 dBm CW (100 W) Max.

P8T-0R5G18G-60-R-SFF-PN is a high speed, single pole, eight throw, reflective switch with a frequency range of 0.5 to 18.0 GHz with an isolation of 55 dB minimum.

EQL-26D5G40G-1D5DB-292MF is a 26.5 to 40.0 GHz, Passive Amplitude Equalizer with a negative slope.  This Equalizer has a maximum input power of 0.5 W.

HP0R5G-18G-CD-SFF is a broadband high pass filter having a passband of 0.5 to 18 GHz. Cut-Off Frequency is 0.5 GHz with a passband insertion loss of 2.0 dB from 1 to 16 GHz. 

DTA-26R5G40G-30-CD-1 is a 10-Bit Programmable Attenuator with a frequency range of 26.5 to 40 GHz with an insertion loss of 6 dB and an attenuation range of 30 dB.

LM-1G18G-15-3W-500WP-SFF is a high-power limiter that operates over the 1.0 to 18.0 GHz frequency range. 

Model HPF130-140-NFF-50W is a High Power, High Pass filter having a cut-off frequency of 130 MHz and a upper passband of 550 MHz.  

PS-500M2G-10B-SFF-MIL-SM is a 0.5 to 2 GHz digitally controlled phase shifter with capability for phase shifting from 0º to 360º with an insertion loss of 8 dB

PA-2G18G-43-5-40-SFF is a high-power amplifier designed for a remarkably low noise figure of 3.5 dB and Psat of 40 dBm (10 W) over the 2 to 18 GHz frequency range with a high gain of +43 dB and ±1.5 dB gain flatness. 

DLVA-70M-80-15V is a Successive Detection Log Video Amplifier (SDLVA) designed to operate over the 50 to 90 MHz frequency range. 

DTA-100M40G-30-CD-1-BCD is a 6-bit programmable 30 dB pin diode attenuator with step resolution of 1 dB over the frequency range of 100 MHz to 40 GHz.

7SFB9500-18G-CD-SFF is a seven-channel switch filter bank. This model has seven filter channels that cover the frequency range of 0.5 to 18.5 GHz

LM-10M14G-100W-1KWP-SFF-OPT17-ROHS is an RF Limiter that works in the frequency range of 10 MHz to 7.0 GHz. 

TD-30T-218-FC-HS-ROHS is a high-speed threshold detector designed to operate over the 2.0 to 18.0 GHz frequency range.

PEC-42-500M40G-20-12-292MF-BG is a 500 MHz to 40 GHz low noise amplifier that has a typical gain of 42 dB while maintaining a ±2.5 dB flatness.

GMDA-S4080-60 is a Detector Log Video Amplifier (DLVA) that operates in the 4 to 8 GHz frequency range and offers a dynamic range of -55 dBm to +5 dBm.

 PS-360-DC-3 OPTION 618-15D-10BIT is a 10-Bit, digitally controlled Phase Shifter operating over the 6.0 to 18.0 GHz frequency range. 

PDRO-6800M-13DBM-SFF is a Dielectric Resonator Oscillators (DRO) with an output frequency of 6800 MHz and a minimum output level of +13 dBm.

LM-10M35G-15DBM-4W-292FF is a passive high-power limiter that operates in the frequency range of 10 MHz to 35 GHz. This model can handle an input power of 25 Watts CW (20 MHz - 18 GHz) and 50 to 40 Watts pulse peak power (20 MHz - 18 GHz).

PS-2G6G-8B-SFF is a 8-Bit Digital Phase Shifter that operates over the 2.0 to 6.0 GHz frequency range. This model offers 360° of phase shift having a LSB of 1.4°. 

 DTA-26R5G40G-30-CD-1 is a 10-Bit Programmable Attenuator with a frequency range of 26.5 to 40.0 GHz. 

P8T-0R5G18G-60-R-SFF-PN is a high speed, single pole, eight throw, reflective switch with a frequency range of 0.5 to 18.0 GHz with an isolation of 55 dB minimum, and an insertion loss of 4.5 dB typical

PEAFS3-14-0R2535R0-6R5-23-12-292FF is a 0.25 to 35 GHz low noise amplifier with a gain of 14 dB, a gain flatness of 1.5 dB, a noise figure of 6.5 dB, an OP1dB of 23 dB, and a VSWR of 2.0:1.

PDPS-3F-6-AL is a 6-Bit Phase Shifter with a Speed of 300 ns Maximum, (100 ns Typical), Designed to Operate at a Frequency of 2.3 to 3.8 GHz with a VSWR of 2.0:1. 

HP3G55M18G-SMA is a High Pass Filter with a frequency range of 3.55 to 18.0 GHz. It has cut-off frequency of 3.145 GHz and an insertion loss of 0.56 dB.

LM-0118-10-1W-SHS-2-FM is a high-power limiter that operates from 100 MHz to 18 GHz that handles 100 W peak power with a pulse width of 1 µs. 

PEC-20-200M6G-3R0-25-SFF is a 200 MHz to 6.0 GHz Low Noise Amplifier that has a gain of 20 dB with ±1.5 dB flatness, OP1dB OF +25 dBm minimum and a noise figure of 3.5 dB. 

SDLVA-1G20G-55-12-SFF is a miniature Successive Detection Log Video Amplifier supplied in our standard PE2 housing that can be used in connectorized or strip line applications.

PEAFS3-14-0R2535R0-6R5-23-12-292FF is a 0.25 to 35 GHz Low Noise Amplifier with a gain of 14 dB, a gain flatness of 1.5 dB, and a noise figure of 6.5 dB.

PDC-800M2D5G-30C-NFF-60W is an 800 MHz to 2.5 GHz Directional Coupler with a frequency range of 0.8 to 2.5 GHz and has an insertion loss of 0.04 dB. 

HP-26D5G-40G-CD-292FF is a High Pass Filter with a passband of 26.5 to 40.0 GHz. It has an insertion loss of 1.1 dB, a rejection of 67.76 dBc, and a VSWR of 1.8:1.

 8SFB-2G18G-SFF is a Switch Filter Bank with a frequency range of 2.0 to 18.0 GHz and has an insertion loss of 8 dB typical.

P4T-100M53G-100-T-RD-185MM is an absorptive single pole four throw pin diode switch that operates over the 100 MHz to 53 GHz frequency range. 

PEC-14-2G18G-4-27-15-SFF is a 2 to 18 GHz medium power, low noise amplifier offering 13 dB gain and an OP1dB of +27 dBm with a low noise figure of 4 dB. 

APD-2-800M2D5G-NFF-50W is a Two-Way Power Divider designed for broadband use and high reliability. Operates over the frequency range of 0.8 to 2.5 GHz and features an insertion loss of ≤0.4 dB,

P3T-8G12G-70-T-SFF is an Absorptive, High Speed, Single Pole, Three Throw, Absorptive Switch with a frequency range of 8.0 to 12.0 GHz and an insertion loss of 2.8 dB.

PCH-180-5R6G5R8G-SFF is a Hybrid Coupler with a frequency of 5.6 to 5.8 GHz and is operational from 5.4 to 5.9 GHz.

HP-26D5G-40G-CD-292FF is a High Pass Filter with a passband of 26.5 to 40.0 GHz. It has an insertion loss of 2.0 dB, a rejection of 54 dBc, and a VSWR of 2.0:1.

 6SFB-30M600M-CD-SFF is a Switched Filter Bank with a frequency range of 30 to 600 MHz and has an insertion loss of 4.5 dB.

PMI Model P6T-2G20G-55-T-SFF is an absorptive, single pole, six throw pin diode switch that operates over the 2.0 to 20.0 GHz frequency range and has a minimum isolation of 55 dB.

P4T-500M40G-60-T-55-292FF-SP Single Pole, Four Throw, Absorptive Switch with a frequency range of 0.5 to 40.0 GHz and an insertion loss of 6.5 dB.

APD-4-218-LC-2 is a High Reliable Four Way Power Divider featuring Excellent Amplitude and Phase Balance, Low Insertion Loss, and High Isolation Electrically Power Divider that operates over the 2.0 to 18.0 GHz frequency range. 

PMC-9D5G10D5G-7D6-SFF is a Monopulse Comparator operating over the 9.5 to 10.5 GHz frequency range. This model offers a maximum 7.6 dB insertion loss while maintaining a maximum amplitude balance of ±0.5 dB.

EQL-DC40-10-292MF is a Passive Equalizer with a frequency range of DC to 40.0 GHz. This unit has an insertion loss of 12.0 dB at 10 MHz, a VSWR of 1.6:1 Typ, an input power of +30 dBm, and an amplitude accuracy of ±2 dB Typ. 

QC-1G18G-SFF-50W is a Hybrid Coupler that operates over the frequency range of 1.0 to 18.0 GHz and has an insertion loss of 2.3 dB, an isolation of 15 dB Min, and a VSWR of 1.6:1.

 PEC-30-0R2520R0-5R0-22-12-SFF is a 0.25 to 20 GHz, low noise amplifier that provides 25 dB of gain with a gain flatness of ±1.5 dB and OP1dB of +22 dBm. 

TD-30T-SHS-218-AMP-OPT4G4D5G-40DBM is a Threshold Detector with a frequency range of 4.0 to 4.5 GHz and a fixed threshold level of -39.2 dBm. It has an operating input power level of -35 to -15 dBm.

PVA-500M18G-60-SFF is a Variable Attenuator that operates over the 0.5 to 18.0 GHz frequency range. This model has an insertion loss of 4 dB and a VSWR of 1.8:1.

APD-2-192212-SFF is a 2-Way Power Divider with a frequency range of 19.2 to 21.2 GHz. This model offers an insertion loss of 0.52 dB, a VSWR of 1.3:1, and an isolation of 21.5 dB.

PDT-8G12G-40-515-SFF is a Two-Way, High-Power Switch with a frequency range of 8.0 to 12.0 GHz. It has an insertion loss of 1.93 dB, a VSWR of 1.28:1, an isolation of 54 dB, and a switching speed of 100 ns.

P2T-1R2G1R4G-60-T-SFF is a Single Pole, Two Throw, Absorptive Switch with a frequency range of 1.2 to 1.4 GHz. It has an insertion loss of 0.83 dB, an isolation of 86 dB, a VSWR of 1.2:1, and a switching speed of 50 ns. 

PDC-3336-6-20W-SFF is a Directional Coupler that operates over the frequency range of 33.0 to 36.0 GHz. It has an insertion loss of 1.07 dB, a VSWR of 1.46:1, and a directivity of 10 dB.

PMI Model No. P16T-250M18G-60-T-512-SFF-DEC-1W is a Single Pole, Sixteen Throw, Absorptive Switch with a frequency range of 0.25 to 18.0 GHz. 

 P2T-1R2G1R4G-25-R-SFF-250W is a Single Pole, Two Throw, Reflective Switch that has a frequency range of 1.2 to 1.4 GHz. 

PDC-192212-6-20W-SFF is a Directional Coupler with a frequency range of 19.2 to 21.2 GHz, a 0.77 dB insertion loss and a 1.25:1 VSWR, a 19 dB directivity.

 LM-20M20G-18-20WP-5W-MAH is a Limiter with a frequency range of 20 MHz to 20.0 GHz. 

PE2-20-1G40G-5R5-15-12-292FF is a low noise amplifier that operates over the frequency range of 1.0 to 40.0 GHz and provides +20 dB Min gain.

EQL-26D5G40G-1D5DB-292MF is a 26.5 to 40.0 GHz, Passive Amplitude Equalizer with a negative slope.  

 P4T-100M18G-80-T-515-SFF-4W-IND is a Single Pole, Four Throw, Absorptive Switch that operates over the 0.1 to 18.0 GHz frequency range. This model has a maximum insertion loss of 6.0 dB.

APD-8-0R523G-292FF is an 8-Way Power Divider that operates in the 0.5 to 23.0 GHz frequency range. This model offers a maximum insertion loss of 7.0 dB, a typical isolation of 15 dB, and a maximum VSWR of 2.0:1. 

 LM-20M20G-18-20WP-5W-MAH-SMM is a Limiter with a frequency range of 20 MHz to 20.0 GHz with an insertion loss of 2.5 dB Max, and a VSWR of 2.0:1

PA-2G18G-43-5-40-SFF is a high-power amplifier with an operating frequency of 2 to 18 GHz offering remarkably high gain of +43 dB Typ/+35 dB Min and saturated output power of 40 dBm (10 W) Typ / 35 dBm Min.

P8T-0R5G18G-60-T-SFF-PN is a Single Pole, Eight Throw, Absorptive Switch that operates over the frequency range of 0.5 to 18.0 GHz.

PEC3-40-30M26R5G-6R0-12-12-SFF is a 30 MHz to 26.5 GHz Low Noise Amplifier that provides greater than 35 dB of gain while maintaining a maximum gain flatness of ±3.5 dB maximum over the operating frequency.

BA-400M1400M-63DB-6B-SFF is a Bi-Directional Switched Bit Attenuator operating from 400 to 1400 MHz. Designed to be switched between a low loss state and 6 set attenuation states. 

LM-1G2G-4CW-1KWP-SMF-ROHS is an RF Limiter that operates in the 1.0 to 2.0 GHz frequency range. This limiter can handle 4 W CW and 1 kW peak. 

 PE2-35-8G12G-2R5-15-12-SFF is a Low Noise Amplifier with a frequency range of 8.0 to 12.0 GHz. It has a minimum gain of 30 dB, a maximum gain flatness of ±1.0 dB.

P2T-218-60-R-1W-SFF is a reflective, single pole two throw switch that operates over the 2 to 18 GHz frequency range. 

P2T-DC18G-10-R-5V-SFF-HIP10W is a Single Pole, Two Throw, Reflective Pin Diode Switch with a frequency range of DC to 18.0 GHz with an isolation of 22.87 dB.

BPF3D875-2D25-CD-SFF is a Band Pass Filter with a passband of 2.75 to 5.0 GHz, an insertion loss of 2 dB, a maximum input power of 33 dBm, and a maximum VSWR of 2.0:1.

PIM-333M368M-28-816-5V-SFF Variable Frequency Comb Generator with an input frequency from 333 to 368 MHz and 2.0 to 16.0 GHz output.

PDVAN-5010-60-8-OPT810 is an 8-bit programmable 60 dB pin diode attenuator with step resolution as low as 0.25 dB over the frequency range of 8.0 to 10.0 GHz and has an attenuation accuracy of ±0.60 dB @ 10 dB, ±0.90 dB @ 20 dB, ±1.5 dB @ 40 dB, and ±1.6 dB @ 60 dB.

PS-3R5G6R5G-10B-SFF is a 10-Bit Digital Phase Shifter that operates over the 3.5 to 6.5 GHz frequency range and offers 360° phase shift having a LSB of 0.35°.  

 LP2400-3G-SFF is a Lowpass Filter that offers extremely high Q with broadband performance and typical insertion loss of 3.5 dB. Ideal for eliminating broadband harmonics and spurs. 

PMI-AFD4-020080-23P-SMA is a 2.0 to 8.0 GHz Amplifier that has a maximum gain of 35 dB, maximum gain flatness of ±2.0 dB, a maximum noise figure of 3.5 dB and a maximum VSWR of 2.0:1. 

DTA-812-BA-80-14B-SFF OPT10D27 is a Digitally Tuned Attenuator covering the 8 to 12 GHz frequency range and optimized for 10.27 GHz.  

PDC-800M2D5G-6C-SFF-50W is an 800 MHz to 2.5 GHz directional coupler having a 6 dB coupling factor and 20 dB directivity. 

 PMC-16G17G-SMA is a monopulse comparator operating over the 16 to 17 GHz frequency range. This model offers a maximum 2.6 dB insertion loss while maintaining a maximum amplitude balance of ±0.8 dB.

 PS-360-2832-5-292FF-OPT10B is a Digitally Controlled Phase Shifter that operates over 28.0 to 32.0 GHz frequency range with a phase shifting range from 0 to 349˚.

P2T-500M18G-30-R-SFF is a Single Pole, Two Throw, Reflective Switch that operates from 500 MHz to 18 GHz which handles +23 dBm CW input power.  

ERDLVA-218-CW-75MV is a CW Immune ERDLVA that operates from 2.0 to 18.0 GHz and has a TSS of -42 dBm, a log slope of 75 ± 10 mV per dB, and a rise/recovery time of 25 ns/500 ns.

QUANTIC PMI Model No. 6SFB-55185-SMA is a 6-Channel Switch Filter Bank that operates over the frequency range of 5.5 to 18.5 GHz.

HPF-4G18G-CD-SFF is a High Pass Filter with a passband of 6.0 to 18.0 GHz. This model has a maximum insertion loss of 1.5 dB.

P2T-218-60-515-R-SFF is a 2.0 to 18.0 GHz Single Pole, Two Throw, Reflective Switch having a 60 dB minimum isolation and a 1.8 dB maximum insertion loss. 

TD-30T-SHS-218-AMP-OPT4G4D5G-40DBM is a Threshold Detector that operates from 4.0 to 4.5 GHz with a maximum input power level of +10 dBm and a typical propagation delay of 10 ns.

 PCH-180-2R15G3G-SFF is a 180° Hybrid Coupler with an operating frequency range of 2.15 to 3.0 GHz. This Coupler has a maximum insertion loss of 0.6 dB.

 QC-7G18G-SFF-30W is a 90° Hybrid Coupler with a frequency range of 7.0 to 18.0 GHz. 

PMI Model  that operates in the 1.0 to 2.0 GHz frequency range. This model offers a typical gain of 26 dB: a maximum gain flatness of ±1.0 dB.

PMI Model No. PS-812-360-14B-SFF OPT10D27 is a Digitally Tuned Phase Shifter that operates from 8.0 to 12.0 GHz, optimized for 10.27 GHz, and has a survival input power level of +30 dBm and an insertion loss of 12 dB. 

PMI Model Number with working frequency range of 10 MHz to 20 GHz that offers up to +28 dB minimum gain @ 20 GHz with a typical gain flatness of ±2.5 dB typical.

PMI Model No.  that operates from 100 MHz to 18 GHz, offers 30 dB of attenuation in 1 dB steps with insertion loss of typically 5 dB; VSWR In/Out of 2.5:1 and Attenuation Accuracy of ±2.5 dB.  

PMI Model No. LM-10M18G-16-20W-AL-ROHS is a 0.01 to 18.0 GHz Limiter.

PMI Model No. P1T-500M18G-80-R-SFF-SW21841A is a 0.5 to 18.0 GHz Single Pole, Single Throw, Reflective Switch that offers a maximum insertion loss of 2.5 dB with a maximum VSWR of 1.9:1 and a minimum isolation of 80 dB.

 P2T-0R75G18G-80-R-512-SFF is a single pole, double throw, reflective switch that operates from 750 MHz to 18.0 GHz which handles 1 Watt CW input power.

PMI Model No. P2T-1R2G1R4G-25-R-SFF-250W is a single pole two throw, hermetically sealed reflective switch designed to operate over the 1.2 GHz to 1.4 GHz frequency range.

APD-2-500M2G-SFF-30W is a two-way power divider featuring Insertion Loss of 0.5 dB; VSWR In/Out of 1.25:1/1.20:1; Isolation of 20 dB; Amplitude Balance of ±0.2 dB; Phase Balance of ±2° and Power Handling of 30 W Forward, 1 W Reversed. 

 LM-0518-10-1W-SHS-1-F is a high speed, high power, hard diode limiter that operates over the frequency range of 0.5 to 18.0 GHz.

PMC-9D5G10D5G-7D6-SFF is a Monopulse Comparator operating over the 9.5 to 10.5 GHz frequency range.

PDVAN-8018-60-8 is an 8-bit programmable 60 dB pin diode attenuator with step resolution as low as 0.25 dB over the frequency range of 8.0 to 18.0 GHz with an Insertion Loss of 3.7 dB.

SDLVA-1G20G-58-12-SFF is a 1.0 to 20.0 GHz SDLVA.  Excellent performance is packed into this ultra-small package. Its ultra-wide frequency range and 59 dB dynamic range makes this part suitable for a multitude of applications. 

PIMA-26-4C-PD2-BPF-L is an integrated microwave assembly consisting of 4 independent channels. Each channel incorporates a 2-way power divider and a bandpass filter that operates in the 2 to 6 GHz frequency range. 

LM-10M18G-16-20W-AL is a coaxial limiter with an operating range of 10 MHz to 18.0 GHz. This model has a maximum insertion loss of 2.0 dB at -10 dBm input power with a VSWR of 2.0:1 maximum.

PMI Model No. TD-30T-SHS-218-8G12G-PECL is an 8 to 18 GHz, Threshold Detector and has a Max VSWR @ -20 dBm of 3.0:1 and a dynamic range of up to +10 dBm.   Min Signal Level for Logic 1 is -20 dBm @ 2.0 GHz and -17 dBm @ 18.0 GHz.

 PIA-12D8G-CD-1, Phase Locked, Dielectric Resonator Oscillator has Internal Reference having an output frequency of 12.8 GHz and provides a minimum output of +13 dBm with all spurs held to -80 dBc, harmonics held to -25 dBc.

PMIX-4D4G7D8G-1G4D4G-12V is a 4.4 to 7.8 GHz, Down Converter Module that has a typical gain of 3 dB; a Max VSWR of 6.5:1; RF Input Power -15 dBm Typ., -10 dBm Max; LO Input 8.8 GHz; LO Input Power +18 dBm Typ.

P1T-DC40G-65-T-24FM-1NS is an Absorptive, Single Pole, Single Throw Pin Diode Switch that operates from DC to 40 GHz with Isolation of 65 dB.

FD-160M-100M-1515 is a frequency discriminator that operates at a center frequency of 160 MHz.  Operating Frequency is 110 to 210 MHz.

DTA-0R5G18G-60-CD-4 is a non-reflective, 10 bit, programmable 60 dB pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 0.5 to 18.0 GHz.

GMDA-D1003 is a Detector Log Video Amplifier (DLVA) that operates between the 7.0 to 18.0 GHz frequency range with a dynamic range of 75 dB; a log slope of +25 ± 1.0 mV/dB.

P8T-100M50G-90-T-RD is a SP8T Absorptive Switch that operates over the 0.1 to 50.0 GHz frequency range with a typical insertion loss of 9.0 dB.

 EQL-26D5G40G-1D5DB-292MF is a 26.5 to 40.0 GHz, Passive Amplitude Equalizer with a negative slope.  Specification include Maximum Input Power of 0.5 W CW.

PMI Model No. DTA-0R5G18G-60-CD-4 is a non-reflective, 10 bit, programmable 60 dB pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 0.5 to 18.0 GHz.

PMI Model No. SDLVA-1G20G-58-12-SFF is a 1.0 to 20.0 GHz SDLVA.  Excellent performance is packed into this ultra-small package. Its ultra-wide frequency range and 59 dB dynamic range.

PMI Model No. PD5-1G18G-10DB-4WAY is a 4-Way Power Divider offers a 4.4 to 18.0 GHz Frequency Coupled Output with 10 dB ± 2 dB insertion loss. 

Model LM-0518-10-1W-SHS-2-M-1218 is a high-power limiter that operates from 12.0 to 18.0 GHz. This limiter handles 100 Watts Peak Power with a pulse width of 1 µs with an insertion loss of 1.5 dB typical. 

PMI Model No. LPF-12G-35-SFF is a Low Pass Filter that operates over the DC to 10.4 GHz frequency range with a Max passband insertion loss of 2 dB; -3 dB and Cut-Off Frequency 12.5 GHz Max.

PMI Model No. P8T-0R120G-110-T-512-SFF is a Single Pole, Eight Throw, Absorptive Switch that operates over the 0.1 to 20.0 GHz frequency range with a Max insertion loss of 6 dB.

PTRAN-100M18G-SDLVA-2SFB-3UVPX-P4-MAH fits a 3U Open VPX form factor utilizing high-speed VITA 67 connector. Up-converts 100 MHz-4 GHz transmit signal to 2-18 GHz.

TD-1G12G-RL-CD-SFF is a high-speed threshold detector designed to operate over the 1.0 to 12.0 GHz frequency range.

SBA-218-63DB-6B-SFF is a Switched Bit Attenuator operating from 2.0 to 18.0 GHz with a maximum insertion loss of 7 dB at 2.0 GHz, 10.5 dB at 18.0 GHz.

P2T-2G18G-60-T-SFF-PM-I is a Single Pole, Two Throw, Absorptive Switch that operates over the 2.0 to 18.0 GHz frequency range with a maximum insertion loss of 3.0 dB.

APD-8-6G18G-SFF is a 6.0 to 18 GHz, 8-Way, In-Phase Power Divider having an insertion loss of 2.0 dB maximum with a minimum isolation of 18 dB. 

P1T-18G40G-30-1515-292FF a SPST, Absorptive Switch that operates over the 18.0 to 40.0 GHz frequency range. 

SDLVA-0R5G18G-50R-30DBM is an SDLVA designed to operate over the 0.5 to 18.0 GHz frequency range for ultra-high-speed applications while maintaining flatness and accuracy.

LM-150M5G-200CW-2KWPK-AGAL is a High-Power Limiter that operates over the 0.15 to 5.0 GHz frequency range and a maximum insertion loss of 2 dB.

PE2-36-26D540G-5R0-10-12-292FF is a Low Noise Amplifier that operates over the 26.5 to 40.0 GHz frequency range; typical gain of +36 dB.

LPF-6G-35-SFF is a Low Pass Filter that operates over the DC to 4.4 GHz frequency range with a maximum passband insertion loss of 2 dB.

P32T-0R5G18G-60-T-SFF-OPT0812 is a 0.5 to 18.0 GHz, Single Pole, Thirty-Two Throw, Absorptive Switch with a maximum insertion loss of 9.5 dB.

LM-150M5G-200CW-2KWPK-AGAL is a Limiter that operates over the 0.15 to 5.0 GHz frequency range. 

 P2T-2G18G-55-T-512-SFF-LV-SP is a Single Pole, Two Throw, Absorptive Switch that operates over the 2.0 to 18.0 GHz frequency range. 

PEC-50-500M40G-20-12-292FF-BG is a 500 MHz to 40 GHz Low Noise Amplifier that has a typical gain of 50 dB while maintaining a ±2.5 dB flatness.

P6T-2G18G-55-R-512-SFF is a Single Pole, Six Throw, Reflective Switch that operates over the 2.0 to 18.0 GHz frequency range. 

TCDRO-12G-CD-1 is a Temperature Compensated Dielectric Resonator Oscillator with a center frequency of 12.0 GHz. 

PE2-19-6G18G-1R6-12-SFF is a Low Noise Amplifier that operates over the 6.0 to 18.0 GHz frequency range. It has a typical gain of 19 dB and a maximum noise figure of 2.5 dB and VSWR 2.0:1 Max.

LM-400M2G-20-1W-SFF is a coaxial limiter that operates over the 400 MHz to 2.0 GHz frequency range. This model offers a maximum of 0.7 dB insertion loss while handling 1 W CW maximum. 

P3T-2G18G-60-T-SFF-REVB-SP is a Single Pole, Three Throw, Absorptive Switch that operates over the 2.0 to 18.0 GHz frequency range and has a maximum insertion loss of 3.2 dB and a minimum isolation of 60 dB.  

LM-150M5G-200CW-2KWPK-AGAL-NFF Ultra-high Power Limiter operates in the frequency range 150 MHz to 5 GHz, with 200 W of CW power handling (+53 dBm), and peak power typically 2 kW (+63 dBm).

PA-218-25G-6NF-34PS-24V-SFF is a High-Power Amplifier that operates over the 2.0 to 18.0 GHz frequency range.  

P4T-500M40G-60-T-55-292FF-SP Rev. B is a 500 MHz to 40 GHz, Ultra-Compact, High Speed, Single Pole, Four Throw, Absorptive Switch. This switch offers over 60dB of port-to-port isolation.

HP8G-7D8G-CD-SMF is a High Pass Filter with a Passband of 8.0 to 22.0 GHz. 

LM-10M9G-100CW-1KWP-SFF is a RF Limiter that operates in the 10 MHz to 9 GHz frequency range.

PEAFS3-14-10M22G-292FF is an Ultra-Low Noise Amplifier that operates over the 10 MHz - 22 GHz and offers a typical gain of +14 dB.

P32T-0R5G18G-60-T-SFF-OPT50M4G is a High Speed, Single Pole, Thirty-Two Throw, Absorptive Switch that operates over 50 MHz to 4.0 GHz.

 6SFB-1G20G-LP-AMP-SFF-MS is a 6-Channel Switch Filter Bank that operates over the 1.0 to 20.0 GHz frequency range. 

P3T-89-45-R-SFF is a Single Pole, Three Throw, Reflective Switch that operates over the 8.0 to 9.0 GHz frequency range.

LM-2G18G-18-20W-1KWP-SFF is a high-power limiter that operates over the 2 to 18 GHz frequency range and capable of handling an input power of 20 W CW and 1000 Watts peak.

PEC-42-1G40G-20-12-292FF-BT is a 1 to 40 GHz low noise amplifier that has a typical gain of 40 dB while maintaining a ±2.5 dB flatness. 

LM-20M18G-100W-15DBM is an RF Limiter that operates in the frequency range of 20 MHz to 18.0 GHz. This limiter can handle up to 100 Watts CW more than 20 MHz to 18.0 GHz.

PS-2G6G-8B-SFF is a 8-Bit Digital Phase Shifter that operates over the 2.0 to 6.0 GHz frequency range with a typical insertion loss of 10.5 dB and a maximum switching speed of 500 ns.  

PDVAN-8018-60-8-OPT25DBM is an 8-Bit digitally programmable attenuator that operates over the frequency range of 8.0 to 18.0 GHz.  

LM-150M5G-200CW-2KWPK-AGAL is a ultra-high power limiter operating in the frequency range 150 MHz to 5 GHz with 200 W of CW power handling (+53 dBm), and more.

SP16T operates over the 26 to 40 GHz frequency range with a typical insertion loss of 12.5 dB while maintaining a typical isolation of 80 dB.   

BPM-2G18G-180-SFF-MB is a Bi-Phase Modulator operating over the 2.0 to 18.0 GHz frequency range and offers insertion loss of 5.5 dB Max while maintaining a minimum isolation of 20 dB.

LM-0R3G8G-14-100W-SFF is a high power limiter operating in the frequency range of 0.3 to 8 GHz with 100 W of CW power handling (+50 dBm).

PDVAN-8018-60-8-OPT25DBM is an 8-Bit digitally programmable attenuator that operates over the frequency range of 8.0 to 18.0GHz.  This model offers low loss of 3.6 dB typically and an attenuation range of 60 dB. 

PMI Model No. LM-2G4G-15-100W-SFF is a high power limiter operating in the frequency range 2.0 to 4.0 GHz (Usable 1.0 to 5.0 GHz) with 100 W CW of power handling (+50 dBm).

P2T-100M44-50-T-292FF-PH is an absorptive, single pole, two throw pin diode switch that operates over the 0.1 to 44.0 GHz frequency range.

P3T-89-45-R-SFF is an 8.0 to 9.0 GHz, single pole, three throw, reflective switch capable of switching within 100 ns maximum with a typical insertion loss of 2.7 dB.

PMI Model: APD-8-0R523G-292FF-MS is an eight-way power divider operating over the 0.5 to 23.0 GHz frequency range.

PEC2-1R8G6R2G-17DBM-LM-SFF is a 1.8 to 6.2 GHz limiting amplifier that provides a limited output power level of +12 dBm to +17 dBm for an input power range of -67 to +10 dBm.

PMI Model No. PEC-40-25-0R518-20-12-SFF-TTLVG is a Dual Gain Amplifier operating over the frequency range of 0.5 to 18.0 GHz.  

PE2-30-218-4R0-20-12-SFF-BT is a 2.0 to 18.0 GHz Low Noise Amplifier that has an integrated bias-tee network on the output port. 

PEC-100M20D1G-20LM-SFF OPT-25DBM is a limiting amplifier covering the RF frequency range of 100 MHz to 20.1 GHz.  Features a minimum limiting input range of -25 to +16 dBm.

SDLVAC-0120-70M is a miniature successive detection log video amplifier that operates over the 0.1 to 2.0 GHz frequency range.

LM-10M62G-20DBM-1W-24FF is a limiter passive has been designed for minimal insertion loss that operates over the 10 MHz to 62 GHz frequency range.

PS-360-DC-3 OPTION 812-15D is an 8-bit digital controlled phase shifter operating over the 8.0 to 12.0 GHz frequency range. This high-speed phase shifter has a 360° range with an LSB of 1.4°. 

PMI Model No. PE2-19-6G18G-1R6-16-12-SFF is a low noise amplifier which operates between 6.0 to 18.0 GHz.

PEC2-50M2500M-2DBM-LM-SFF is a 50 MHz to 2500 MHz limiting amplifier that provides a limited output of 2 dBm ± 3.5 dB over an input power range of -50 to +30 dBm CW.

LM-10M62G-20DBM-1W-24FF is a limiter passive has been designed for minimal insertion loss that operates over the 10 MHz to 62 GHz frequency range.

PDVAT-100M20G-30-8B is a 8-Bit programmable 30 dB PIN diode attenuator with a step resolution as low as 0.25 dB over the frequency range of 100 MHz to 20.0 GHz.

P4T-100M53G-100-T-RD is an absorptive, single pole four throw pin diode switch that operates over the 100 MHz to 53 GHz frequency range. 

 LM-10M40G-15DBM-4W-AGAL is a limiter passive designed for minimal insertion loss that operates over the 10 MHz to 40.0 GHz frequency range.

PMI Model No. LPF6-712-SFF is a Microstrip Lowpass Filter offers a high Q and low insertion loss. 

LM-10M35G-15DBM-4W-292FF is a passive limiter that operates in the frequency range of 10 MHz to 35 GHz.

PMI Model: APD-8-0R523G-292FF is an eight-way power divider operating over the 0.5 to 23.0 GHz frequency range.

P1T-8G40G-65-T-292FF-1NS-LVPECL is a 8.0 to 40.0 GHz, single pole, single throw, absorptive switch and has a Min isolation of 55 dB;  a Mx insertion loss of 6.8 dB and more.

PE2-15-2R012R0-4R0-22-12-SFF is a Low Noise Amplifier operating over the frequency range of 2.0 to 12.0 GHz.  

SDLVA-218-64-70MV-CW -100 is a CW immune SDLVA that operates from 2.0 to 18.0 GHz and is designed for MIL standard environments with humidity sealed SMT circuits.

EQL-17D5G21D5G+8DB-292MF is a passive amplitude equalizer that operates over the frequency range of 17.5 to 21.5 GHz.

LM-20M18G-100W-15DBM is an RF Limiter that operates in the frequency range of 20 MHz to 18.0 GHz. It handles up to 100 W CW more than 20 MHz to 18.0 GHz.

PS-12-360-QQ1470 option 107 is a 1.7 GHz, digitally controlled analog phase shifter with capability for phase shifting from 0 to 360º.

PLA-14D65G15G35G-20DB-SFF-250W is an integrated limiter and attenuator that operates at 14.65 to 15.35 GHz.

P16T-250M18G-60-T-512-SFF-DEC-1W is a single pole, sixteen throw absorptive pin diode switch (SP16T) configuration that operates from 0.25 to 18.0 GHz.

APD-2-100M18G-CD-1 is a 2-Way power divider that operates over the frequency range of 0.1 to 18.0 GHz.

P2T-OR5G8G-45-R-50W-AL Is a single pole, two throw reflective switch designed to operate over the 0.5 GHz to 8.0 GHz frequency range.

PMI Model No. PIQ-85M18G-36020-CD-2 is a vector modulator covering the frequency range of 85 MHz to 18 GHz.

PTB-40-0R118-6R5-21-120VAC-1U-SFF-OPT10M6G is an Integrated Microwave Assembly operating over the frequency range of 10 MHz to 6.0 GHz..

PMI Model Number: PEAFS3-14-0R2535R0-6R5-23-12-292FF is a 0.25 to 35.0 GHz low noise amplifier.

PMI Model No: PEC2-1G12G-60-21DBM-LM-PP is an integrated RF module that contains an input limiter.

P2T-6G18G-40-R-570-TFF-50WCW is a single pole, two throw, reflective switch that operates over the 6.0 to 18.0 GHz frequency range.

PTRAN-100M18G-SDLVA-SFB-3UVPX-10HP-MAH-MX is a transceiver covers the frequency range of 100 MHz to 18.0 GHz and fits into a 3U open VPX form factor.

PRX-20-1G18G-850M-SFF is a channelized receiver that operates over the frequency 1.0 to 18.0 GHz.

PL-ENET-18BIT-0V5V-2X is a dual microprocessor module with a DC power of 6 V @ 1 A and a voltage protection of ±10 V.

PMC-9G10G-7D9-SFF is a Monopulse Comparator operating over the 9.0 to 10.0 GHz frequency range.

LM-100M20G-18-10W-SFF-MAH is a 10 W peak, 1 W CW Limiter that works from 0.1 to 20.0 GHz in an ultra-small package with low Insertion Loss of 3 dB Max.

QC-5010-NFF is a 5.0 to 10.0 GHz Hybrid Coupler. It has a maximum insertion loss of 1.1 dB, a minimum isolation of 16 dB and more.

BPF-4829M-30DB is a 4829 MHz Band Pass Filter and specifications include 3 dB Bandwidth of 210 MHz Typ.

PMI Model No. PS-360-3237-8-292FF is an 8-bit digitally controlled, phase shifter operating over the frequency range of 32.0 to 37.0 GHz.

HBDFM-218-BD-DP, is a high band direction finding module from 2.0 to 18.0 GHz, Uni-Directional, Multi-Function Device.

PMI Model No. PEC-30-8G12G-6R0-28-15-SFF is an amplifier that operates from 8.0 to 18.0 GHz.

SDLVA-8G18G-40-5-SFF, a Successive Detection Log Video Amplifier operates on a single +5 VDC supply and consumes less than 130mA of current.

CMDA-4D1G6D1G-3TTL-SFF-DP is a 4.1 to 6.1 GHz, Coarse Microwave Discriminator centered at 5.1 GHz. Using state of the art MMIC and MIC technology.

DTA-12G26G5-60-10D is a 10-bit programmable 60 dB pin diode attenuator operating over the frequency range of 12.0 to 26.5 GHz.

PMI Model No. DTA-1G18G-60-7-CD-1-HERM that operates over the frequency range of 1.0 to 18.0 GHz. It has a maximum insertion loss of 5 dB and a maximum VSWR of 2.0:1.

PMI Model No. P16T-100M20G-60-T-512-SFF-DEC is a single pole, sixteen throw, absorptive pin diode switch that operates from 0.1 to 20.0 GHz.

2SFB-8G26G-CD-SFF Rev C is a 2-channel switch filter bank providing a low-pass filter that passes 8.62 to 8.70 GHz with a rejection band of 17.24 to 17.4 GHz.

PMI Model PS-2G18G-360-12D-TS is a 2 to 18 GHz, 12-BIT, vector phase shifter making it ideal for frequency translation where continuous monotonic phase shifting is required.

PMI Model No. 6SFB-HF-CC-100M18G-MAH-RX-TX is an integrated module containing two 5-Channel Switched Filter Bank covering 100 MHz to 18.0 GHz.

Model SDLVA-0120-70-100M2G-10DBM is a SDLVA that operates between the 0.1 to 2.0 GHz frequency range. it has a dynamic range of 70 dB minimum and a TSS of -65 dBm.

PMI Model No. APD-7-328M335R5M-TNC is a 7-way power divider that operates over the frequency range 328 to 335.5 MHz. 

DTA-2G18G-60-CD-2-OPT-1G18G is a non-reflective, 10 BIT, programmable 60 dB, pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 1.0 to 18.0 GHz. 

2SFB-8G26G-CD-SFF Rev C is a 2-channel switch filter bank providing a low-pass filter that passes 8.62 to 8.70 GHz with a rejection band of 17.24 to 17.4 GHz. 

PMI Model No. LM-10M2D5G-100CW-1KWP-SFF is a RF limiter that operates in the 10 MHz to 2.5 GHz frequency range.  This limiter can handle 100 W CW and 1 KW peak. 

P6T-2G18G-55-R-512-SFF is a high speed, single pole, six throw, reflective switch capable of switching within 15 ns. The frequency range is 2.0 to 18.0 GHz and has over 55 dB of isolation.

PMI Model No. PEC-22-24G40G-4R0-24-292FF is a low noise amplifier that operates over the 24.0 to 40.0 GHz frequency range and provides 22 dB minimum of gain.

PMI Model DTA-30M6G-60-CD-1 is a 8-Bit programmable 60 dB PIN diode attenuator with a step resolution as low as 0.25 dB over the frequency range of 30 MHz to 6.0 GHz.

SDLVA-2020-70-0518 is a truly DC-coupled successive detection log video amplifiers available in Extended 70/75 dB dynamic range over the range of 0.5 to 18 GHz bandwidth, with true DC coupling.

Model JTIDS-0001-TNS is an ultra-small band reject filter centered at 1085 MHz. This filter rejects frequencies from 960 to 1210 MHz and was specifically designed for Military JDITS applications. 

PMI Model No: P1T-DC40G-65-T-292FF-1NS-OPT2G6G-LVTTL is a SPST Absorptive, FET switch that operates from 2.0 to 6.0 GHz. Specifications include Isolation, 65 dB Typ, 55 dB Min; Insertion Loss, 2.5 dB Typ and more.

Model No. SDLVA-8G18G-40-5-SFF is an 8-18 GHz successive detection log video amplifier that operates on a single +5 VDC supply and consumes less than 130 mA of current. It is highly temperature compensated such that the log linearity is better than +/-1 dB over the temperature range of -54 to +85 °C.

PMI Model No. DLVA-18G40G-42-50-CD-1 is a DLVA operating over the frequency range of 18.0 to 40.0 GHz. with performance optimized over the frequency range of 30.0 to 31.0 GHz. This unit features TSS: -34 dBm; Log Dynamic Range: -32 dBm to +10 dBm and more.

PMI Model No. FD-0518-10-2G4G is a 2.0 to 4.0 GHz, frequency discriminator having a VSWR of 2.0:1 maximum, 1.5:1 typical, and a video output slope of 1V/GHz, frequency discriminator accuracy: ±100 MHz, Operating Input Power: +10 dBm nominal, ±0.1 dBm.

PMI Model No.P2T-8G18G-50-R-SFFF is a reflective single pole, two throw, high power pin diode switch that operates from 8.0 to 18.0 GHz. This device offers high isolation: 50 dB typical, low insertion loss: 3 dB typical; isolation: 50 dB minimum, and fast switching 200 ns.

PMI Model No: P2T-500M18G-80-T-515-SFF-4W is a SP2T absorptive, PIN diode switch that operates over the 0.5 to 18.0 GHz frequency range. This switch handles a maximum RF Input Power of 4 W CW and has a maximum switching speed of 200 ns.

PMI Model No. LM-100M20G-18-10W-SFF is a 10 W peak, 1 W CW Limiter that operates over the 0.1 to 20.0 GHz frequency range.  This model offers a maximum insertion loss of 2.0 dB and a maximum VSWR of 2.0:1. 

PMI Model PE2-16-300M20G-1R7-15-12-SFF works from 300 MHz to 20 GHz, with noise figure of 3 dB at 300 MHz and 18 GHz, single supply voltage of +12 to +15 volts at 90 mA current, with a gain of 12 dB to 16 dB and P1dB of 13 dBm.

PMI Model No. P20T-7G18G-80-T-515-SFF-SP is an absorptive, single pole, twenty throw, pin diode switch that operates over the 7.0 to 18.0 GHz, frequency range. This model incorporates a TTL compatible driver for easy system integration.

PMI Model No. LM-1G18G-16-4W-SMF is a coaxial limiter with an operating range of 1.0 to 18.0 GHz. This model has a maximum insertion loss of 2.3 dB at -10 dBm input power, with a maximum VSWR of 2.0:1.

PMI Model No. LM-1G18G-15-3W-500WP-SFF is a high-power limiter that operates over the 1.0 to 18.0 GHz frequency range. This model is capable of handling an input power of 3 W CW and 500 W peak.

PMI Model No. EWDM-2G8G-65-70MV is a CW immune EW detector module operating over the 2.0 to 8.0 GHz frequency range. This model features an internal switch used to switch between the Bit IN and RF IN with input blanking on both ports.

PMI Model No. EWDM-8G18G-65-70MV is a CW immune EW detector module operating over the 8.0 to 18.0 GHz frequency range. This model features an internal switch used to switch between the Bit IN and RF IN with input blanking on both ports.

PMI Model No. ERDLVA-2G8G-65-70MV is a 2.0 to 8.0 GHz, CW immune ERDLVA. This model features an internal switch used to switch between the Bit in and RF In with input blanking on both ports.

PMI Model No. PDVAT-0518-60-8-93-10M18 is an 8-Bit programmable 60 dB PIN diode attenuator with a step resolution as low as 0.25 dB over the frequency range of 10 MHz to 18.0 GHz.

PMI Model No. P2T-0R5G8G-45-R-SFF-50W-SM is a SP2T reflective switch designed to operate over the 0.5 to 8.0 GHz frequency range and to handle 50 W average input power.  

PMI Model No. P4T-10G40G-60-T-292FF is a SP4T solid-state, absorptive switch that operates from 10 to 40 GHz.  This model offers over 60 dB of isolation and less than 6 dB insertion loss. 

PMI Model No. PDPS-3F-6 Option AL is a six bit phase shifter with a speed of 300 ns maximum, (100 ns typical), designed to operate at a frequency of 3.0 GHz with a VSWR of 2.0:1.  This unit has a typical insertion loss of 9.0 dB and a phase accuracy of ±6° maximum.

PMI Model No. SDLVA-500M4G-CD-2 is a successive detection log video amplifier (SDLVA) that offers a typical RF gain of 55 dB. This model has a log slope of 25 mV/dB typical into a 50 Ohm load with input power handling of +17 dBm CW maximum.

PMI Model No. PE2-16-300M20G-1R7-15-12-SFF is a low noise amplifier that works from 300 MHz to 20 GHz. This amplifier has a very low noise figure over this broad frequency range. This low noise amplifier provides 16 dB of small signal gain while requiring only a single supply of +12 V. The P1dB output power of 15 dBm allows this low noise amplifier to function as a lo driver for balanced, I/Q or image reject.

PMI Model No. LM-100M20G-18-10W-SFF is a 10 W peak, 1 W CW Limiter that operates over the 0.1 to 20.0 GHz frequency range.  This model offers a maximum insertion loss of 2.0 dB and a maximum VSWR of 2.0:1. The unit is supplied with SMA female connectors in an ultra small housing measuring only 0.50" x 0.50" x 0.22". 

PMI Model No. APD-8-100M-28V is an 8-way, amplified power divider module to provide a 100 MHz signal to 8 outputs with less than 4 dB ±1.5 dB Max - Measured 3.1 dB of loss.  This module balances a low noise figure with high output power.  Other specifications VSWR of 2.0:1 Max. - Measured 1.1:1 In/1.25:1 Out, Noise Figure of 9.0 dB Max., 6.0 dB goal - Measured 7.9 dB and more.

PMI Model No. QC-5D3G6G is a quadrature coupler that operates over the frequency range of 5.3 to 6.0 GHz.  This model provides low loss of 1 dB and an isolation of 18 dB minimum.  The VSWR is 1.4:1 maximum into a 50 ohm impedance.  The amplitude balance is ±0.7 dB maximum and the phase balance is ±5° maximum. 

PMI Model No: FD-30M-6M-1515 is a frequency discriminator that operates at a center frequency of 30 MHz.  It has a peak to peak bandwidth of 10 MHz and a linear bandwidth of 6 MHz minimum with a dynamic range of -10 to -0 dBm.  The sensitivity into 50 Ohms is 1000 mV/MHz.  This device offers a maximum rise time of 120 ns and the size is 4.63" x 1.50" x 0.47".

PMI Model No. HP8G-7D8G-CD-SFF is a high pass filter with a passband of 8.0 to 22.0 GHz and a -3 dB cut-off frequency of 7.8 GHz. It has a maximum passband insertion loss of 1.5 dB and maximum passband VSWR of 2.0:1. This model is supplied with SMA female connectors in a housing measuring 1.15" x 0.70" x 0.50".

PMI Model No. PE2-30-8R018R0-3R5-22-12-SFF is an 8.0 to 18.0 GHz, low noise amplifier with a typical gain of 30 dB while maintaining a maximum gain flatness of ±1.5 dB over the operating frequency.  The typical noise figure is 3.5 dB and offers a minimum OP1dB of 20 dBm.  The operating voltage is +12 to +15 VDC with a maximum current draw of 325 mA. 

PMI Model No. EQL-17D6G21D6G-2DB-292MF is a passive amplitude equalizer that operates over the frequency range of 17.6 to 21.6 GHz.  This unit has a maximum input power of 0.5 W CW and a maximum VSWR of 2.0:1. This model is supplied with a 2.92 mm female input connector and a 2.92 mm output connector. 

PMI Model No. P7T-2G18G-60-T-1W is a single pole, seven throw absorptive switch with phase and amplitude matching of ±6° and ±0.5 dB respectively, relative to J2. This model has also been designed to operate over the 2.0 to 8.0 GHz, frequency range with low in-band video leakage of -65 dBm.   

PMI Model No. BPF-11D825D-1D85G-60DB-SFF is a band pass filter centered at 11.825 GHz. The 1 dB bandwidth is 1850 MHz. Insertion loss 3 dB maximum, rejection -60 dBc minimum at 9.15 to 9.9 GHz and -60 dBc minimum at 13.75 to 14.5 GHz and VSWR 2.0:1. 

PMI Model No. P6T-2G18G-55-R-512-SFF is a high speed, single pole, six throw, reflective switch capable of switching within 15 ns.  The frequency range is 2.0 to 18.0 GHz and has over 55 dB of isolation. This model was designed to produce very low video transients of 15 mV peak to peak and a video transient spectral content of -65 dBm maximum. 

PMI Model Number TD-1G12G-RL-CD-SFF-NH is a high speed threshold detector designed to operate over the 1 to 12 GHz frequency range, with an adjustable threshold level of -30 to -10 dBm, VSWR of 3.0:1 Typical. This Unit comes in a very small size with field removable SMA connectors on the input and output.

DTA-2G18G-60-CD-2-OPT-1G18G is a non-reflective, 10 BIT, programmable 60 dB, pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 1.0 to 18.0 GHz. Specifications include insertion loss of 4.5 dB; VSWR 2.0:1 maximum; attenuation accuracy of ±1.0 dB at 0 to 20 dB, ±1.5 dB at 20 to 40 dB and ±2.0 dB at 40 to 60 dB; typical attenuation flatness of ±1.0 dB at 20 dB, ±1.25 dB at 40 dB and ±3.0 dB at 60 dB; switching speed 1.0 µs.

PMI Model No. PE2-30-1R018R0-4R5-22-12-SFF-1 is a 1.0 to 18.0 GHz, low noise amplifier that typically provides 30 dB of gain while maintaining a maximum gain flatness of ±1.5 dB over the operating frequency. The noise figure is 4.5 dB maximum and offers an OP1dB of 22 dBm minimum.  The operating voltage is +12 to +15VDC with a typical current draw of 500 mA. 

PMI Model No. EWDM-2G6G-65-70MV is a CW immune EW detector module operating over the 2.0 to 6.0 GHz frequency range. This module features an internal switch used to switch between the "Bit In" and RF In" with input blanking on both ports. In addition, two amplified RF outputs are provided a 7 dB gain channel and a 33 dB gain channel. The video output is designed to drive a 150 ft. cable, while maintaining high speed, and excellent accuracy.

PMI Model No. LM-618-10-1W-SHS-1-M is a high speed, high power limiter that operates from 6.0 to 18.0 GHz.  This limiter handles 100 W Peak Power with a pulse width of 1usec.  The insertion loss is only 1.5 dB typically and has a VSWR of 2.0:1 maximum.  This limiter is supplied in a small housing measuring only 0.5" x 0.5" x 0.22".

PMI Model No. PS-360-3237-8-292FF is a high speed, millimeter wave, 8-bit digitally controlled, phase shifter that operates over the frequency range of 32.0 to 37.0 GHz. This phase shifter offers a low insertion loss of 13 dB typically and maintains a VSWR of 1.8:1. The total phase shift range is 358.593° having a step size of 1.406° and switches between states in less than 500 ns. 

PMI Model No. PSX-500M18G-60-SFF is a pin diode transfer switch that operates over the 500 MHz to 18 GHz frequency range.  Specifications include 60 dB minimum isolation, 3.0 dB maximum insertion loss, VSWR In/Out 1.9:1 maximum, +20 dBm CW maximum input power and 100 ns maximum switching speed. This model incorporates a TTL compatible driver for easy system integration.

PMI Model No. LM-618-10-1W-SHS-1-M is a high speed, high power limiter that operates from 6.0 to 18.0 GHz.  This limiter handles 100 W peak power with a pulse width of 1 usec. The insertion loss is only 1.5 dB typically and has a VSWR of 2.0:1 maximum. 

PMI Model No. GMTA-1002 is a threshold detector designed to operate over the frequency range of 2.0 to 18.0 GHz. It has a threshold level of -23 dBm with threshold stability of +/-3.0 dBm over frequency and temperature. Other specifications Input Operating Range of -18 to -23 dBm, Input VSWR 2.5:1 maximum, maximum input power level +10 dBm (without damage), Response Time Any Input Greater than 3 dB = 100 µs and operates using +12 VDC at 50 mA maximum. 

PMI Model No. PE2-30-1R018R0-4R5-22-12-SFF-1 is a 1.0 to 18.0 GHz, low noise amplifier that typically provides 30 dB of gain while maintaining a maximum gain flatness of ±1.5 dB over the operating frequency. The noise figure is 4.5 dB maximum and offers an OP1dB of 22 dBm minimum The operating voltage is +12 to +15VDC with a typical current draw of 500 mA. 

PMI Model No. PS-360-3237-8-292FF is a High Speed, Millimeter Wave, 8-Bit Digitally Controlled, Phase Shifter that operates over the frequency range of 32.0 to 37.0 GHz. This phase shifter offers a low insertion loss of 13dB typically and maintains a VSWR of 1.8:1. The total phase shift range is 358.593° having a step size of 1.406° and switches between states in less than 500 ns. This model provides a high level of accuracy by offering an amplitude error of ±1.5dB and a phase shift error of ±1.3°. 

PMI Model No. SDLVA-218-60-70MV-CW is a CW immune SDLVA (Successive Detection Log Video Amplifier). This unit operates from 2.0 to 18.0 GHz and has the ability to interface with a long cable (65 FT), while maintaining high speed, flatness and accuracy.  Specifications include frequency flatness:  ±2.0 dB Typ, Signal Capability:  Pulse (100 ns to 300 µs), Pulse on CW TSS: (-20 ºC to +85 ºC) -66 dBm for 10 MHz Video Bandwidth and Log Dynamic Range  -60 dBm to 0 dBm.

PMI Model No. TD-30T-SHS-218-AMP-OPT4G4D5G-40DBM is an ultra-high speed, high sensitivity threshold detector optimized for the 4.0 to 4.5 GHz frequency range.  This unit has a fixed threshold level of -40 dBm.  It is a miniature unit with TTL output logic. Package size 2.5"(L) x 2.0"(W) x 0.5"(H) with SMA (F) connectors.

PMI Model No. DLVA-8G10G75-50-SFF is an 8.0 to 10.0 GHz, detector log video amplifier. This unit has a dynamic range of -75 to 0 dBm, a log linearity of ±1.8 dB, and a log slope of 50 ± 4 mV/dB. Other specifications include Frequency Flatness of±1.2 dB, TSS of -78 dBm, Log Linearity ±1.8 dB - Measured ±1.3 dB,  Log Slope 50 ± 4 mV/dB, and Output DC Offset 50 ± 50 mV.  Power Supply: +15 V at  350 mA, -15 V at 100 mA and SMA (F) connectors. 

PMI Model No. PE2-500M18G-5R0-21-12-SFF is a 0.5 to 18.0 GHz, low noise amplifier that provides 24 dB min of gain while maintaining a maximum gain flatness of ±2.0 dB over the operating frequency.  The noise figure is 5.0 dB maximum and offers a typical OP1dB of 21 dBm.  The operating voltage is +12 to +15 VDC with a nominal current draw of 375 mA. 

PMI Model No. PLNA-35-100M18G-P1dB24-120VAC is a portable amplifier that operates over the 100 MHz to 18.0 GHz frequency range.  This model provides 40 dB typical gain with a minimum OP1dB of +24 dBm, Gain Flatness: ±2.0 dB Typical, VSWR In/Out: 2.0:1 Typical and Noise Figure: 3 dB. This amplifier features an illuminated push button On/Off switch in a small package (3.0" x 3.0" x 1.75") with Type N connectors.  Gold plated finish.

PMI Model No. LM-10M2D5G-100CW-1KWP-SFF is a RF limiter that operates in the 10 MHz to 2.5 GHz frequency range.  This limiter can handle 100 W CW and 1 KW peak (1% duty cycle, 1 µs maximum pulse width) input power and provides a maximum leakage of +13 dBm CW input.  This module has a low insertion loss of 0.5 dB and a recovery time of 2 µs typical. 

PMI Model No. PDT-8G12G-40-515-SFF is an 8.0 to 12.0 GHz, 2 way high power switch that has an insertion loss of 2.0 dB maximum and a VSWR of 1.8:1 maximum. The operating power is +40 dBm CW average, +57 dBm 1 µs, 1% duty cycle with an isolation of 40 dB minimum.  Switching Speed 200 ns maximum - measured 100 ns, power supply requirements +5 V at 100 mA and -15 V at 60 mA.  Features include SMA female connectors.

PMI Model No: LNA-35-500M2D5G-0D6-25-12-SFF is a low noise amplifier operating over the 0.5 to 2.5 GHz, low noise amplifier.  This model offers a typical gain of 35 dB while maintaining a typical gain flatness of ±1.6 dB and a maximum noise figure of 0.6 dB. This compact model is outfitted with SMA female connectors in housing measuring 1.25" x 1.25" x 0.563".

PMI Model No. DTA-14G40G-32-CD-2 is a 10 Bit programmable attenuator with step resolution as low as 0.04 dB which provides over 32 dB of attenuation over the frequency range of 14.0 to 40.0 GHz.  This model is offered in a slim line housing measuring 2.0" x 1.8" x 0.5" with 2.92 mm female connectors and operates on a single +15 VDC supply with only 40 mA of current consumption typically. Specifications include Insertion Loss 9.0 dB Typical, VSWR 2.0:1 and Attenuation Flatness ±1.5 dB Typical, Attenuation Accuracy ±2.0 dB Typical. 

PMI Model PS-2G18G-360-8D is a 2 to 18 GHz, 8-Bit, vector phase shifter making it ideal for frequency translation where continuous monotonic phase shifting is required.  This model features high speed switching (<410 ns measured), phase shift 360° with a ±15° accuracy (typical), 18.0 dB maximum insertion loss  and typically lower than 60 dB harmonic distortion.   Package Size: 4.25” x 3.50” x 1.00”, SMA(F) connectors,DC-37P,  Sub Miniature D Multi-Pin control connector and operates using ±12V to ±15V at ±100 mA maximum.

PMI Model No. P2T-50M40G-95-T-515-SFF-OPT18G is an absorptive, single pole, two throw, pin diode switch that operates over the 50 MHz to 18 GHz frequency range.  This model incorporates a TTL compatible driver for easy system integration.  Features include SMA female connectors. Unit size is 1.25" x 1.25" x 0.4" with painted blue finish. 

PMI Model No.P2T-1G18G-10-R-528-SFF-HIP10W is a single pole, two throw, reflective switch capable of operating with an input power of 10 W CW over the 1.0 to 18.0 GHz frequency range.  This model features high input power handling capability while offering very fast switching speeds of 40 ns.  This switch is compact in size and weight and only consumes 2.5 mA of positive and 2.5 mA of negative DC current making it suitable for a wide range of applications.   Features include SMA female connectors, and TTL - Single Line. Unit size is 1.2" x 1.0" x 0.5".  

PMI Model No. P2T-6G18G-40-R-570-TFF-1D6KW is a reflective 1.6 kilowatt high-power cold switching single pole double throw switch operating in the 6.0 to18.0 GHz frequency range.  Features include TNC female connectors. Unit size is 2.00" x 2.00" x 0.75" with painted blue finish. 

PMI Model No: P1T-DC40G-65-T-292FF-1NS-OPT18G-50OHM is a SPST Absorptive, FET switch that operates from DC to 18.0 GHz.  The typical Isolation is 60 dB with an Insertion Loss of 4.5 dB typical and a 6 ns Switching Speed (On/Off) and a 2 ns Rise/Fall.  SMA female connectors (J1 - J2) and SMC control connector.  The size is 1.30" X 1.20" X 0.50".  

PMI Model No. P2T-1G1R1G-25-R-SFF-100W-SM is a single pole, two throw, hermetically sealed reflective switch designed to operate over the 1.0 to 1.1 GHz frequency range.  This model is designed to handle 100 Watts average input power and 5 kW peak having a 17 µs pulse width and 2% duty cycle.  Features include TNC female connectors. Unit size is 3.25" x 2.75" x 0.70".

PMI Model No. DPX-18G26R5G40G is an ultra small, low loss diplexer for use over the frequency range of 18.0 to 40.0 GHz.  This model is designed to have a crossover frequency at 26.5 GHz and greater than 60 dB of rejection.  Features include 2.92mm female connectors. Unit size is 0.80" x 0.60" x 0.38". 

PMI Model No. HPF18G-DC15G is a low loss ultra-small high pass filter with a passband frequency range of 18.0 to 26.5 GHz and greater than 60 dB rejection from DC to 15.0 GHz.  Features include 2.92mm female connectors. Unit size is Features include 2.92mm female connectors. Unit size is 0.64" x 0.58" x 0.38". 

PMI Model No. PIA-12D8G-CD-1 is a Phase Locked, Dielectric Resonator Oscillator with Internal Reference having an output frequency of 12.8 GHz.  This model provides a minimum output of +13 dBm with all spurs held to -80dBc and harmonics held to -25 dBc.  The frequency stability is ±3 ppm with an internal reference of 100MHz.  The phase noise is as follows: -34 dBc/Hz at 1 Hz, -65 dBc/Hz at 10 Hz, -85 dBc at 100 Hz, -10 8dBc/Hz at 1 kHz, -115 dBc/Hz at 10 kHz, -12 0dBc/Hz at 100 kHz, and -140 dBc/Hz at 1 MHz offsets. 

PMI Model No. 11DP-11R5/16R5-CD-SFF-1 is a diplexer that offers pass bands at 10.75 to 12.25 GHz and 15.75 to 17.25 GHz.  The pass band insertion loss is less than 3 dB and the VSWR is 1.5:1 maximum.  Filter channel 1 has a pass band of 10.75 to 12.25 GHz and offers -50 dBc of rejection at 10.25 GHz and -75 dBc of rejection at 13.75 GHz.  Filter channel 2 has a pass band of 15.75 to 17.25 GHz and offers -50 dBc of rejection at 17.75 GHz and -75dBc of rejection at 14.25 GHz. 

PMI Model No. 2SFB-8G26G-CD-SFF Rev C is a 2 channel switch filter bank providing a low-pass filter that passes 8.62 to 8.70 GHz with a rejection band of 17.24 to 17.4 GHz.  In by-pass mode the unit passes signals from 8.0 to 26.5 GHz.  This unit is powered by a +5 V single supply and the control logic is TTL/CMOS +5 V compatible.

PMI Model No. BP13G-10G-CD-SFF is a suspended substrate bandpass filter that offers a wide passband of 8 to 18 GHz.  This filter offers a low insertion loss of 1.5 dB typically and a passband VSWR of 2.0:1 maximum.  Stopband rejection of 70 dB typical is provide from DC to 6 GHz and from 20 to 23 GHz. 

PMI Model DTA-26R5G40G-30-CD-1 is a 10-Bit programmable 30 dB PIN diode attenuator with a step resolution of 0.03 dB over the frequency range of 26.5 to 40 GHz. This model operates on a single +15 VDC supply and draws only 50 mA of current. Very high levels of attenuation accuracy of 0.03 dB is achieved.  This attenuator provides ultra-fast switching speeds of 300 ns and has an operating input power rating of +10 dBm. 

PMI Model No. SDLVA-50M18G-70 is an SDLVA (successive detection logarithmic video amplifier) operating in the 50 MHz to 18 GHz frequency band. It features a built in voltage variable threshold detector circuit that is set up to match the video output voltage to within 5%. In addition, this model has a TSS of -70 dBm and a dynamic range of 70 dB, all in a package measuring only 2.3" x 2.2" x 0.4" with SMA female connectors.

PMI Model No. PS-2G6G-8B-SFF is an 8-Bit digital phase shifter that operates over the 2.0 to 6.0 GHz frequency range.  This model offers 360° of phase shift having a LSB of 1.4°.  The insertion loss is 10.5 dB typical with a typical phase accuracy of ±0.5°, Amplitude error of ±1 dB typical.  Supplied in a housing measuring 3.25" x 3.25" x 0.94" with SMA female connectors.

PMI Model Number: PEC4-16-50M18G-4R0-19-15-SFF is a 50 MHz to 18.0 GHz compact amplifier. Specifications include maximum input power of +23 dBm CW, gain of +14 dB minimum. 19 dB  maximum, gain flatness of ±2.0 dB max, noise figure of 4.0 dB typical, OP1dB +19 dBm minimum and VSWR 2.0:1 max. - measured 1.43:1/ 1.50:1.  This amplifier is supplied with SMA female connectors in our standard PEC4 housing with gold plated finish.

PMI's A-Series amplifiers are available in low noise, medium power and lost cost designs and operate over the 10 MHz to 40 GHz frequency range. These new models feature form fit & function design, low noise figure, operating temp: -54° to +85°C, unconditionally stable over temperature, excellent group delay and phase linearity, field replaceable SMA connectors, and more.

PMI Model No. DP-5700M-6500M-CD-SFF is a diplexer with a low passband of 5700 to 6500 MHz and high passband of 13750 to 14500 MHz.  This unit offers SMA female connectors, power handling of 20 W, channel to channel isolation of > 70 dB and passband insertion loss of <1 dB. Specifications include VSWR 2.0:1 at Passbands - measured 1.37 dB and CH to CH Isolation >=70 dB - measured 83.19 dB.

PMI Model No. P8T-20M6G-80-R-515-SFF  is a single pole, eight throw, reflective switch module with low insertion loss, high isolation and an integral decoded 3-bit TTL driver designed for 20 MHz to 6.0 GHz operation.  The unit has a maximum switching speed of 250 ns and maximum operating power of 23 dBm CW max. Specifications include frequency 20 MHz to 6.0 GHz and insertion loss 2.75 dBtyp, 3.25 dB max and measured 2.91 dB.

PMI Model No. PS-255-2G18G-8B-SFF is a 2 to 18 GHz 8-bit digitally controlled phase shifter with capability for phase shifting from 0° of 255° with resolution as fine as 1.0°. This unit has a typical insertion loss of 18 dB and a typical VSWR of 2.5:1. The DC voltage requirement is +12 to +15 V with typical current draw of 200 mA. The unit is supplied in a housing measuring 2.0" x 2.1" x 0.5".

PMI Model No. LM-18G40G-SMT-1 is a high power limiter capable of withstanding an input power level of 20 W, 440 to 670 nsec Pulse Width, PRF 600 to 900 kHz, 40% Duty Cycle.  This model operates in the 18 to 40 GHz frequency range.  The insertion loss is 4.0 dB maximum, VSWR of 2.0:1 and 250 nsec response time.  This limiter is supplied on a surface mount / drop-in carrier that measures 0.198" x 0.270" x 0.016".

PMI Model No. APD-4-3D13D5-40W-SFF is a 3.1 GHz to 3.5 GHz 4-Way Power Divider that offers maximum insertion loss of 0.45 dB with 23 dB minimum port to port isolation. This power divider is port to port phase matched within ±2°. Field removable SMA female connectors are offered in a housing measuring 2.56" x 1.77" x 0.44". Specifications include frequency range 3.1 to 3.5 GHz and insertion loss <=0.45 dB - measured 0.19.

PMI Model No. P4T-500M18G-80-T-515-SFF-2W-IND is a single pole, four throw, absorptive switch. This switch offers 80 dB of isolation and a maximum insertion loss of 6.0 dB.  It has a maximum switching speed of 200 ns with individual TTL control.  The operating power is +33 dBm CW max and the VSWR is 2.0:1 maximum.

PMI Model No. DTA-500M2G-64-10B-SFF is a 10-Bit programmable 64 dB pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 0.5 to 2.0 GHz.  Specificatins include frequency rang for 0.5 to 2.0 GHz, Insertion loss 2.7 dB max and VSWR 2.0:1 max. The DTA-500M2G-64-10B-SFF enviromental temperature is -54°C to +85°C operating and -65°C to +125°C non-operating.

PMI Model No. PEC2-2G18G-80DB-21DBM-LM-SFF is a 2.0 to 18.0 GHz, limiting amplifier that provides a limited output power level of +21 to +25 dBm for an input power range of -55 to +10 dBm CW.  This model has output power level versus frequency compensation such that the limited output power has a flat frequency response.  This unit is supplied with SMA(F) connectors in a small housing measuring only 2.98" x 0.78" x 0.26".

PMI Model Number DD-20-218-5PF-1-N-M-OPT0518 is a 0.5 to 18.0 GHz, high speed, high sensitivity, diode detector requiring no bias and offering excellent temperature stability with a response time of less than 5 nanoseconds.  The frequency range is 0.5 to 18 GHz.

PMI Model No. PE2-12-2G4D2G-5R0-17-12-SFF is a 2.0 to 4.2 GHz, low noise amplifier that has a typical gain of +12 dB and maintains a gain flatness of +/-1.0 dB max.  It has a maximum noise figure of 5.0 dB and offers an OP1 dB of +17 dBm min. The unit requires +12 to +15 VDC with a nominal current draw of 230 mA. 

PMI Model No. PE2-22-2G4D2G-3R0-19-12-SFF is a 2.0 to 4.2 GHz, low noise amplifier that has a typical gain of +21.5 dB and maintains a gain flatness of +/-1.0 dB max.  It has a maximum noise figure of 3.0 dB and offers an OP1 dB of +19 dBm min.  The unit requires +12 to +15 VDC with a nominal current draw of 320 mA.

PMI Model No. P4T-100M40G-110-T-512-292FF-IND is an absorptive, single pole, four throw pin diode switch that operates over the 0.1 to 40.0GHz frequency range.  This model incorporates a TTL compatible driver for easy system integration.

PMI Model No. PE2-34-2G18G-3R5-15-SFF-VVG-DD is a voltage variable gain amplifier with integrated diode detector operating over the frequency range of 2.0 to 18.0 GHz.  This amplifier is supplied in our standard PE2 housing that can be used as SMA connectorized or as a surface mount component.  It is optimized for 5.5 to 18.0 GHz

PMI Model No. P1T-500M18G-85-T-SFF is an absorptive, high speed, single pole single throw switch capable of switching within 25 ns typically.  The frequency range is 500 MHz to 18.0 GHz.  This switch has > 85 dB isolation.

PMI Model No. PE2-30-20G20R6G-3R0-10-12-SFF is a 20.0 to 26.5 GHz, low noise amplifier. This amplifier is supplied in our standard PE2 housing that can be used as a SMA connectorized or a surface mount component.

PMI Model No. SDLVA-2020-OPT112 is a truly DC-coupled successive detection log video amplifier (SLDVA) that has 40 dB dynamic range over the frequency range of 1.0 to 12.0 GHz and provides an 8-bit digital log video output. The unit employs planar diode detectors and integrated video circuitry for high speed performance and outstanding reliability. 

PMI Model No. PUC-4G18G-CD-1 is an amplified up/down converter for the frequency range of 4.0 to 18.0 GHz, with an IF range of 10 to 100 MHz.  It features a 32 dB programmable attenuator with 10-bit resolution and an output amplifier to provide conversion gain.  It also features an IF transfer switch to select the upper or lower sideband.

PMI Model No. P8T-100M40G-95-T-512-292FF-IND is a high speed, single pole, eight throw, absorptive switch operating over the frequency range of 100 MHz to 40 GHz. It is capable of switching within 100 ns and has 90 dB of isolation. This model is supplied with 2.92 mm female connectors in a gold plated housing measuring 4.0" x 1.5" x 0.4".

PMI Model No. TDC-30T-0110-CD-1 is a high speed, TTL logic output threshold detector with an input coupler designed to operate from 0.1 to 10 GHz. Specifications include 0.1 to 10 GHz frequency range, 2.5 dB max insertion loss and 2.0:1 VSWR. Finish is gold plated.

PMI Model No. PL-MCU-ENET-TTL-MAH is an ethernet microcontroller test box which allows for an ethernet command to be sent up to 18 parallel TTL output bits.  This controller can be used with many PMI products that require parallel digital commands, such as switches, attenuators, phase shifters and IQ modulators.

PMI Model No. PE2-30-2R04R0-1R5-21-8V-SFF is a 2.0 to 4.0 GHz, low noise amplifier that typically provides 30 dB of gain while maintaining a maximum gain flatness of +/-1.0 dB over the operating frequency.  The typical noise figure is 1.5 dB and offers a minimum OP1 dB of +21 dBm.  The amplifier requires +8 VDC and has a nominal current draw of 300 mA.

PMI Model No. PE2-30-2R04R0-1R5-21-12-SFF is a 2.0 to 4.0 GHz, low noise amplifier that typically provides 30 dB of gain while maintaining a maximum gain flatness of +/-1.0 dB over the operating frequency.  The typical noise figure is 1.5 dB and offers a minimum OP1 dB of +21 dBm.  The amplifier requires +12 to +15 VDC and has a nominal current draw of 300 mA.

PMI Model No. PXO-100M-CD-1 is a 100 MHz, sinewave crystal controlled oscillator with coaxial output connector. This model provides minimum output power of +7 dBm with all spurs held to -60 dBC (10 to 500 MHz) and harmonics and sub-harmonics held to -40 dBc. It requires DC power of +15 V ±5%, 40 mA max, and is in a housing that measures 2.0" x 2.0" x 0.75".

PMI Model No. PLO-9G-CD-1 is a phase locked oscillator with an output frequency of 9.0 GHz.  This model provides minimum output power of +21 dB with all spurs held to -60 dBc and harmonics held to -25 dBc. The unit has a VSWR or <1.5:1 for all phases and is supplied with SMA(F) connectors in a housing that measures 2.25" x 2.25" x 0.63"

PMI Model No. P9T-500M40G-60-R-55-292FF-OPT1222 is a high speed, single-pole-nine-throw reflective switch capable of switching within 100 ns.  The frequency range is 0.5 to 40 GHz (optimized over 12 to 22 GHz), > 60 dB of isolation.

PMI Model No. PE2-34-2G18G-3R5-15-SFF-VVG-DD is a voltage variable gain amplifier with integrated diode detector operating over the frequency range of 2.0 to 18.0 GHz.  This amplifier is supplied in our standard PE2 housing that can be used as SMA connectorized or as a surface mount component.  It is optimized for 5.5 to 18.0 GHz. 

PMI Model No. P2T-1G1R1G-25-R-SFF-100W is a single pole, two throw, hermetically sealed reflective switch designed to operate over the 1.0 to 1.1 GHz frequency range.  This model is designed to handle 100 W average input power and 5 KW peak having a 17 usec pulse width and 2% duty cycle.

PMI Model No. P32T-0R5G18G-60-T-SFF is a high speed, single pole, thirty-two throw, absorptive switch that operates over 500 MHz to 18.0 GHz.  This state-of-the-art switch offers top notch performance of 8.5 dB typical insertion loss and an isolation of 78 dB typically. The switch maintains 2.0:1 maximum VSWR over the full operating frequency with a maximum switching speed of 100 nsec.

PMI Model No. P2T-1G1R1G-25-R-TFF-40W is a single pole, two throw, hermetically sealed, reflective switch designed to operate over the 1.0 to 1.1GHz frequency range.  This model is designed to handle 40 W averageinput powers and 4 KW peak having a 3 usec pulse width and 1 % duty cycle.

PMI Model No. P2T-500M18G-50-T-SFF-I is a terminated, single pole, two throw switch  that operates over the frequency range of 0.5 to 18.0 GHz.  This model handles +23 dBm CW input power with port to port isolation of 50 dB min.  It has a low insertion loss of 2.8 dB max while still offering a fast switching speed of 50 nsec max.

PMI Model No. DTA-14G40G-32-CD-2 is a 10 Bit programmable attenuator with step resolution as low as 0.04 dB which provides over 32 dB of attenuation over the frequency range of 14.0 to 40.0 GHz.  This model is offered in a slim line housing measuring 2.0" x 1.8" x 0.5" with 2.92 mm female connectors and operates on a single +15 VDC supply with only 40 mA of current consumption typically.

PMI Model No. TD-2G18G-RL-CD-SFF is a high speed threshold detector designed to operate over the 2.0 to 18.0 GHz frequency range with an adjustable threshold level of -30 to -10 dBm and a VSWR of 3.0:1 max.  This unit is supplied with field removable SMA Female connectors in a small package measuring 1.1" x 0.6" X 0.19".

PMI Model No. P4T-2G18G-60-T-512-SFF-LV is a 2.0 to 18.0 GHz, single pole, four throw, absorptive, low video transient switch.  This model offers 60 dB of port to port isolation and a maximum insertion loss of 3.2 dB.  It has a switching speed of 50 ns max and is independently TTL controlled with an operating power of +23 dBm CW and a VSWR of 2.0:1.

PMI Model No. P8T-100M40G-85-T-512-292FF is a high speed, single pole, eight throw, absorptive switch operating over the frequency range of 100 MHz to 40.0GHz. It is capable of switching within 30 ns and has over 90 dB of isolation up to 18 GHz, 80 dB up to 26.5 GHz and 70 dB up to 40 GHz.

Model Number PS-5G18G-400-A-SFF is a 5 to 18GHz, low phase noise, analog phase shifter with capability for phase shifting from 0 to 400 degrees.  The unit operates from a single positive control voltage of 0 to +10 VDC with a phase voltage sensitivity of 40 degrees per volt. This model can be used with the SMA connectors or in a surface mount configuration.

PMI Model No. P6T-2G18G-60-T-512-SFF-LV is a single pole, six throw, absorptive, low video transient, solid state switch operating over the frequency range of 2.0 to 18.0 GHz.  This model has a maximum insertion loss of 4.0 dB and a minimum isolation specification of 60 dB with video transients of 2 mV typically.

PMI Model No. DRO-9D7G-CD-1 is a dielectrically stabilized GaAs FET Oscillator with a center frequency of 9.7 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -75 dBc/Hz.  The unit requires +15 VDC and 150 mA and measures 1.35" x 1.98" x 1.04".

PMI Model No. DRO-7D7G-CD-1 is a dielectrically stabilized GaAs FET Oscillator with a center frequency of 7.7 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -80 dBc/Hz.  The unit requires +15 VDC and 150 mA and measures 1.60" x 2.75" x 1.04".

PMI Model No. P2T-100M40G-95-T-512-292FF is an absorptive, single pole, two throw pin diode switch that operates over the frequency range of 0.1 to 40.0 GHz.  This model incorporates a TTL compatible driver for easy system integration.

PMI Model No. DRO-16D3G-CD-1 is a dielectrically stabilized GaAs FET oscillator with a center frequency of 16.3 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -70 dBc/Hz.  The unit requires +15 VDC and 150 mA and measures 1.06" x 1.63" x 0.98".

PMI Model No. DRO-14D3G-CD-1 is a dielectrically stabilized GaAs FET oscillator with a center frequency of 14.3 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -70 dBc/Hz.

PMI Model No. DRO-12D3G-CD-1 is a dielectrically stabilized GaAs FET oscillator with a center frequency of 12.3 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -75 dBc/Hz.

PMI Model No. PIQ-2G18G-360-16-CD-1 is a 2.0 to 18.0 GHz, high performance I/Q Vector Modulator with 2 x 12 bit monotonic TTL compatible channels (I and Q).  This model offers a full 360 degrees of phase shift with a minimum of 16 dB of amplitude control.

PMI Model No. DRO-11D7G-CD-1 is a dielectrically stabilized GaAs FET oscillator with a center frequency of 11.7 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -75 dBc/Hz.

PMI Model No. SDLVA-218-44-70M is a detector log video amplifier (DLVA) designed to operate over the 2.0 to 18.0 GHz frequency range. This model offers a logging range of -40 to +4 dBm having a log slope of 70 mV/dB.  The logging linearity is better than ±0.75 dB and the rise time is 25 nsec maximum and the fall time 300 nsec maximum.  

Model Number DD-20-218-5PF-3-P-M is a high speed diode detector optimized for the 2 to 18 GHz frequency range. This model offers a fast response of 5 nsec, a TSS of -50 dBm at 2 MHz video bandwidth and a Video Capacitance of 5.6 pF. The output voltage polarity is positive, but a negative polarity is available upon request.   

PMI Model No. PE2-30-9R010R0-2R5-21-12-SFF is a low noise amplifier that operates over the 9.0 to 10.0 GHz frequency range.  This model provides a typical gain of 30 dB while maintaining a noise figure of 2.5 dB and a OP1 dB of 21 dBm minimum.  The input and output VSWR is better than 2.0:1 and this model operates on +12 to +15 VDC.  

PMI Model No. TD-6G18G-CD-SFF is a high speed threshold detector designed to operate over the 6.0 to 18.0 GHz frequency range with an adjustable threshold level of -30 to +10 dBm and aVSWR of 3.0:1 max.  The unit is supplied with removable SMA female connectors in a compact housing that measures 1.0" x 0.6" x 0.19".

PMI Model No. PE2-28-218-5R0-12-15-SFF is a 2.0 to 18.0 GHz, low noise amplifier that provides 24 dB min of gain.  The noise figure is 4.5 dB max and offers an OP1 dB of 14 dBm min.  The operating voltage is +15 VDC and the current draw is 200 mA max.  The unit is supplied with removable SMA(F) connectors in our standard PE2 housing.

PMI Model No. 4BP160-20-2A-PP is an LC Bandpass filter centered at 160 MHz with PC Pins in and out.

PMI Model No. 4BP160-10-2A-PP is an LC Bandpass filter centered at 160 MHz with PC Pins in and out.

PMI Model No. 4BP160-5-2A-PP is an LC Bandpass filter centered at 160 MHz with PC Pins in and out.

PMI Model No. P1T-0R5G18G-60-T-512-SFF is a single pole, single throw, absorptive solid state switch that operates over the frequency range of 0.5 to 18.0 GHz.  This model has a maximum insertion loss of 3.5 dB and an isolation specification of 60 dB.  It operates at 20 dBm CW and can survive 1 W CW, 10 W peak for 1 uSec.

PMI Model No. 4BP160-40-2A-PP is an LC Bandpass filter centered at 160 MHz with PC Pins in and out.

PMI Model No. P2T-2G18G-55-T-512-SFF-LV is a terminated, single pole, two throw switch that operates from the 2.0 to 18.0 GHz frequency range and can handle +23 dBm CW input power with port to port isolation of 55 dB min.  This model has low insertion loss while still offering a fast switching speed of 50 nsec max.

PMI Model No. GMDA-D1003 is a detector log video amplifier (DLVA) that operates between the 7.0 to 18.0 GHz frequency range.  It has a dynamic range of 75 dB, a log slope of 25 mV/dB and a nominal video bandwidth of 12 MHz. Furthermore, it has been designed using cutting edge GaAs technology which provides stunning performance and reliability in a compact package.

PMI Model No. PFS-618-CD-1 is a high speed frequency synthesizer that operates over the frequency range of 6.0 to 18.0 GHz.  This model covers the complete 6.0 to 18.0 GHz frequency in 100 kHz steps with an output power of +10 dBm minimum.  The unit is accurate to within ±1 MHz and settles within 1 usec maximum.

PMI Model No. PE2-30-1R018R0-4R5-22-12-SFF-1 is a 1.0 to 18.0 GHz, low noise amplifier that typically provides 30 dB of gain while maintaining a maximum gain flatness of ±1.5 dB over the operating frequency.  The noise figure is 4.5 dB max and offers an OP1 dB of 22 dBm min.  The operating voltage is +12 to +15 VDC with a typical current draw of 500 mA.

PMI Model No. P16T-100M20G-60-T-512-SFF is a single pole, sixteen throw, absorptive pin diode switch that operates at a frequency range of 0.1 to 20.0 GHz.  This model has a typical insertion loss of 8.5 dB and 60 dB of isolation.  It operates at 20 dBm CW and has a survival power of 1 W CW, 10 W peaks for 1 microsecond.

PMI Model No. 024142SA is a successive detection log video amplifier (SDLVA) that operates over a frequency range of 18.0 to 40.0 GHz.  It has a dynamic range of 65 dB, log slope of 25 mV/dB and a nominal video bandwidth of 32 MHz.  It has been designed using cutting edge GaAs technology which provides stunning performance and reliability.

PMI Model No SWN-1170-4DT-SP is a single pole, four throw, absorptive switch designed to operate over the 0.5 to 18.0 GHz frequency range.  This model is designed to maintain low insertion loss, high isolation and fast switching speed.  It is supplied with removable 2.92 mm (F) connectors in a radial housing that measures 1.25" dia x 0.7" thick.

PMI Model No. PIFA-9D4G-1D8G-1 is an integrated frequency down converter used within Doppler Radar Systems.  The RF Input is 9.4 GHz +/- 30 Mhz with an input dynamic range of 100 to 0 dBm.  The LO Input is 2.803 GHz +/- 15 Mhz with a power level of +5 to +7 dBm.  The resulting IF output frequency is 1.8 GHz +/- 10 MHz.

PMI Model No. SWN-2181-TRA is a pin diode transfer switch that operates over a frequency range of 0.5 to 18.0 GHz.  It has 60 dB min of isolation,, max insertion loss of 3.5 dB and a max input power of +10 dBm CW.  This model incorporates a TTL compatible driver for easy system integration and is supplied with removable 2.92 mm (F) connectors in a housing that measures 1.0" x 1.0" x 0.25".

PMI Model No. LM-2G18G-2D8-33DBM-12V is an active limiter that operates over a frequency range of 2.0 to 18.0GHz with max input power of +33 dBm CW and a maximum leakage power of +2.8 dBm. The VSWR is 2.0:1 max the operating voltage is +12 VDC with a current draw of 180 mA max.. The unit is supplied with removable SMA(F) connectors in our standard PE2 housing.

PMI Model No. P2T-8G12G-90-T-SFF is a single pole, two throw terminated solid state switch. This model operates over the frequency range of 8.0 to 12.0 GHz and has a typical insertion loss of 2.4 dB, isolation of 75 dB minimum and a typical switching speed of 15 nsec. This unit is capable of operating with RF input power levels up to 20 dBm CW.

PMI Model No. P2T-9D25G-80-R-SFF-3W is a single pole, two throw, reflective pin diode switch that operates over a single frequency range of 9.25 +/- 30 MHz.  This model has a maximum insertion loss of 34 dBm CW and a minimum isolation specification of 80 dB. It operates at 34 dBm CW max, or +33 dBm, 2 microsecond pulse width (PW) and 8KHz (operating).

PMI Model No. LM-500M8G-2-33DBM-12Vis an active limiter that operates over a frequency range of 0.5 to 8.0 GHz with a maximum input power of +33 dBm CW and a maximum leakage power of +2.3 dBm.  The VSWR is 2.0:1 and the operating voltage is +12 VDC with a typical current draw of 180 mA.  The unit is supplied with removable SMA(F) connectors in our standard PE2 housing.

PMI Model No. LM-8G18G-7-33DBM-12V is an active limiter that operates over a frequency range of 8.0 to 18.0 GHz with a maximum input power of +33 dBm CW and a maximum leakage power of +7.1 dBm.  The VSWR is 2.0:1 and the operating voltage is +12 VDC with a maximum current draw of 100 mA. The unit is supplied with removable SMA(F) connectors in our standard PE2 housing.

PMI Model No. TD-30T-SHS-218-2G4G-PECL is a high speed, LVPECL logic output threshold detector designed to operate from 2.0 to 18.0 GHz, but optimized for 2.0 to 4.0 GHz.  This detector has a propagation delay of 15 ns max and has a LVPECL output.

PMI Model No. PIQ-2G18G-360-16-CD-1 is a 2.0 to 18.0 GHz, high performance I/Q vector modulator with 2 x 12 bit monotonic TTL compatible channels (I and Q).  This model offers a full 360 degrees of phase shift with a minimum of 16 dB of amplitude control.

PMI Model No. PA-40-17D521D5-5R0-36-12-292FF is a medium power amplifier that operates over the frequency range of 15.7 to 21.5 GHz.  It has a nominal gain of 40 dB typical with a maximum gain flatness of +/-1.75 dB and a typical noise figure of 5.0 dB. It is supplied with SMA(F) connectors in a housing that measures 2.6" x 2.0" x 0.5"

PMI Model No. PEC-14-127-8-12-SFF Rev B is a wide band front end amplifier that operates over the frequency range of 1.0 to 26.5 GHz.  This model provides gain of 13 to 17 dBm and has a maximum gain flatness of +/-1.5 dB.  The maximum noise figure is 5.5 dB from 1.0 to 20.0 GHZ and 6.0 dB from 20.0 to 26.5 GHz. The housing measures 0.83" x 0.75" x 0.36" and is supplied with removable SMA connectors.

PMI Model No. PEC2-8G18G-21DBM-LM-SFF is an 8.0 to 18.0 GHz limiting amplifier that provides an nominal output power level of +20.0 dBm for an input power range of -50 to +10 dBm CW.  This model has output power level versus frequency range compensation such that the limited output power has a flat frequency response. The unit is supplied in a small housing measuring only 2.98" x 0.78" x 0.36".

PMI Model DTA-2G18G-60-CD-2-OPT-1G18G is a non-reflective, 10 BIT, programmable 60 dB, pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 1.0 to 18.0 GHz.  This model is offered in a slim line housing measuring only 0.5" H.

PMI Model No. PE2157R52015SFF Rev. D is a 7.5 to 20.25 GHz, low noise amplifier that provides a small gain window of 14.5 to 17.5 with a typical gain flatness of +/-1.5 dB.  The noise figure is 6.0 dB max and offers an OP1 dB of 18.0 dBm min.  The operating voltage is +15 VDC and the current draw is 300 mA max.  This unit is supplied with removable SMA(F) connectors in our standard PE2 housing.

PMI Model No. GMTA-1005 is a threshold detector designed to operate over the frequency range of 8 to 18 GHz.  It has a fixed threshold level of -42 dBm with threshold stability of +/-3.0 dBm over frequency and temperature.

PMI Model No. HADA-D2002 is a Detector Log Video Amplifier (DLVA) that operates between the frequency range of 2.0 to 18.0 GHz.  It has a dynamic range of 40 dB with a log slope of 50 mV/dB and a nominal video bandwidth of 12 MHz.  This unit has been designed with cutting edge technology which provides stunning performance and high reliability in a compact package.

PMI Model No. SDLVA-0R81R6-75-CD-3 is a successive detection log video amplifier (SDLVA) that operates between the 850 to 1550 MHz frequency range.  It has a dynamic range of 75 dB, a log slope of 40 mV/dB and a nominal video bandwidth of 20 MHz.  It has been designed using cutting edge GaAs technology which provides stunning performance and reliability in a compact package.

PMI Model No. LM-8G18G-7-33DBM-12V is an active limiter that operates over a frequency range of 8.0 to 18.0 GHz with a maximum input power of +33 dBm CW and a maximum leakage power of +7.1 dBm.  The VSWR is 2.0:1 and the operating voltage is +12 VDC with a maximum current draw of 100 mA.

PMI model number PIQ-85M18G-360/20-CD-2 is a vector modulator covering the frequency range of 85 MHz to 18 GHz. This unit provides an attenuator resolution of 0.08 dB and a phase shift resolution of 0.703125. The attenuation is phase invariant and the phase is amplitude invariant making it ideal for nulling unwanted signals. The unit can be specifically calibrated for any number of 100 MHz bands within the frequency range.

PMI Model No. PE210R258R515SFFLM Rev. B is a 0.25 to 8.5 GHz, low noise amplifier with a small signal gain window of +9.0 to +13 dB.  The noise figure for this unit is <=4.5 dB max (valid from 0.5 to 8.5 GHz) and offers an OP1 dB of +16 dB min.  The operating voltage is +12 VDC and the current draw is 300 mA max.

PMI Model No. PLN-17-110-15-LCA is a 1.0 to 10.0 GHz, low noise amplifier that typically provides 17 dB of gain.  The typical noise figure is 2.0 dB and offers an OP1 dB of 13 dBm min.  The operating voltage is +12 to +15 VDC and the current draw is 65 mA max.

PMI Model No. PE2-30-1R06R0-1R5-22-12-SFF is a 1.0 to 6.0 GHz, low noise amplifier that provides 30 dB of gain typically.  The typical noise figure is 1.8 dB and offers an OP1 dB of 22 dBm typ.  The operating voltage is +12 to +15 VDC max and the current draw is 320 mA typ.

PMI Model No. PE2-15-8G20G-4R0-20-SFF is a 8.0 to 20.0 GHz, low noise amplifier that provides 12 dB min of gain with a typical gain flatness of +/-1.25 dB. The noise figure is 4.0 dB typ and offers an OP1 dB of 20 dBm typ.  The operating voltage is +11 to +15 VDC and the current draw is 225 mA nom.

PMI Model No. P1T-9D25G-90-T-SFF is a high speed, solid state, single pole single throw switch capable of switching within 20 ns. The frequency range is 9.25 GHz (+/- 30 MHz) with > 90 Db of isolation.

PMI Model No. HADA-D2001 is a detector log video amplifier (DLVA) that operates between the 0.5 to 2.0 GHz frequency range.  It has a dynamic range of 40 dB, a log slope of 50 mV/dB and a nominal bandwidth of 20 MHz.  It has been designed using cutting edge technology which provides stunning performance and reliability in a compact package.

PMI Model No. PEC-42-1G40G-20-12-292FF is a 1.0 to 40 GHz, ultra-wideband low noise amplifier that provides 42 dB of gain typically with a typical noise figure of 5.5 dB.  The OP1dB is typically +22 dBm (1.0 to 18.0 GHz) and +19 dBm (18.0 to 40.0 GHz). The maximum input power rating is +17 dBm CW and the operating DC supply is 550 mA at +12 to +15 VDC. 

PMI Model No. POB-15-818-13-LCA Rev.B is a 8.0 to 18.0GHz, low noise amplifier which provides 15 dB of gain while maintaining a gain flatness of +/-1.5 dB typically over the operating frequency. The noise figure is 3.0 dB typical and offers a typical OP1dB of +13dBm.  The amplifier requires +12 VDC and has a typical current draw o f 75 mA. 

PMI Model No. PM2-34-218-15-SFF-1 is a 2.5 to 18.0 GHz low noise amplifier with a gain window of 32.0 to 36.0 dB at -40ºC to +95ºC and 32.0 to 37.0 dB at -54º Cto +95º C and a gain flatness of +/-1.5 dB max.

PMI Model No. PEAFS3-12-218-15-SFF-1 is a 2.0 to 18.0 GHz low noise amplifier that provides +15 to +22 dB of gain.  The noise figure is 5.0 dB max from 2.0 to 4 GHz and 4.1 dB max at 4.0 to 18.0 GHz and offers an OP1 dB of +9 dBm min.  The operating voltage is +15 VDC and the current draw is 180 mA max.

PMI Model Number PE2-34-1R251R75-12-SFF-1 is a 1.25 to 1.75 GHz, temperature compensated, low noise amplifier with 34 dB of gain with a typical gain flatness of +/-0.25 dB. The noise figure is typically 4.98 dB and offers a minimum OP1 dB of 0 dBm.  The amplifier requires +7 to +12 VDC and the current draw is 198 mA typical.

PMI Model No. APD-4-218 is a high reliable four way power divider featuring excellent amplitude and phase balance, low insertion loss, and high isolation electrically, and removable I/O SMA connectors mechanically.

PMI Model No. P1T-500M40G-55-T-292FF is an SPST, high speed, absorptive switch. This switch operates at a frequency range of .5 to 40.0 GHz and is capable of switching within 100 ns.  It has 55 dB of isolation and insertion loss of 5.5 dB max.

PMI Model DTA-22G28G-50-CD-1 is a 50 dB monotonic programmable attenuator with 11-bit resolution that provides a step size of 0.025 dB. It has also been designed to have very low insertion loss over the frequency range of 22.5 to 27.5 GHz.

PMI Model No. BPF3D875-2D25-CD-SFF is a Bandpass filter that has a center frequency of 3.875GHz and a Passband of 2.25GHz.  The passband insertion loss is 2.0dB max with a VSWR of 2.0:1 max.  The filter measures 2.50" x 0.8" x 0.5" and is supplied with SMA Female connectors.

PMI Model No. P2T-960M977M-30-R-528-SFF-20W is a single pole, two throw, reflective switch capable of handling input power up to 20 W CW. The frequency range is 960 to 977 MHz and it has over 40 dB of typical isolation with a switching speed of less than 40 nsec. The unit is supplied with SMA Female connectors in a package measuring 1.2" x 1.0" x 0.5".

PMI Model No. P2T-8G18G-45-R-SFF-HP20W is an SP2T, high power (20 W), reflective switch.  This switch operates on a frequency of 8.0 to 18.0 GHz.  It has a low insertion loss of 2.5 dB max and an integral TTL driver and is hermetically sealed.

PMI Model No. P2T-8G12G-100-T-55-SFF is a single pole, two throw, high power, absorptive switch.  This switch has high isolation of 100 dB min and low insertion loss of 3.0 dB typical (5.0 dB max).  It offers a high switching speed of 100 ns max and has an integral TTL driver.

PMI Model No. P2T-5G5D15G-30-R-528-SFF-20W is a single pole, two throw, reflective switch capable of handling input power up to 20 W CW. The frequency range is 5000 to 5150 MHz and it has 30 dB of isolation with a switching speed of less than 40 nsec. The unit is supplied with SMA Female connectors in a package measuring 1.2" x 1.0" x 0.5".

PMI Model No. SDLVA-100M4G-CD-2 is a successive detection log video amplifier (SDLVA) that operates between the 100 to 4000 MHz frequency range and is capable of extending to 6000 MHz.  It has a dynamic range of 70 dB, a log slope of 25 mV/dB and a nominal video bandwidth of 11.67 MHz.

PMI Model Number PE2-60-2G8G-2R5-20-12-SFF is a 2.0 to 8.0 GHz low noise amplifier which produces 60 dB of gain with a maximum noise figure of 2.5 dB.  The OP1dB is >20 dBm and the VSWR is 2.0:1 maximum. This amplifier operates on a DC voltage supply of +12 to +15 volts and the current draw is 475 mA maximum.  The housing measures 2.98” x 0.78” x 0.26” and is supplied with SMA female connectors.

PMI Model No. P5T-500M40G-60-T-55-292FF-5G40G is an SP5T, absorptive switch that operates from 0.5 to 40.0 GHz.  This switch has an insertion loss of < 8.0 dB max,  >60 dB of isolation and is supplied in a small housing measuring 1.353" dia x 0.40" thick.

PMI Model No. P8T-500M40G-60-T-55-292FF is a high speed, single pole, eight throw, absorptive switch operating over the frequency range of 0.5 to 40 GHz.  This switch has over 60 dB of isolation and is capable of switching within 50 ns.

PMI Model No. P4T-50M40G-55-T-292FF is a 50 MHz to 40.0 GHz, single pole, four throw, absorptive switch.  This switch offers 55 dB of port to port isolation and a maximum insertion loss of 8 db. It has a switching speed of 100 ns and is independently TTL controlled.  The operating power is +20 dBm CW and it has a VSWR of 2.5:1 max.   

PMI Model No. LM-10G-3-26DBM-12V is an active limiter that operates at 10 GHz and provides an input dynamic range of -45 to +26 dBm.  This limiter offers very hard limiting at 0 dBm typically and 3 dBm maximum.  The VSWR on average is better than 1.4:1 and operating voltage is +12 to +15 VDC with a current draw of 10 0mA.

PMI Model No. PEC-42-500M40G-20-12-292MM is a 500 MHz to 40 GHz ultra-wideband low noise amplifier that provides typically 42 dB of gain with a noise figure of 5.5 dB at 2 0GHz.  The OP1 dB is typically +22 dBm (1.0 to 18.0 GHz) and +1 9dBm (18.0 to 40.0 GHz). 

PMI Model No. SDLVA-2G6G-70-CD-1 is a successive detection log video amplifier (SDLVA) that operates between the 2.0 to 6.0 GHz frequency range. It has a dynamic range of 70 dB, a log slope of 40 mV/dB and offers very fast rise and fall times of 15 and 25 nsec respectively.

PMI Model No. P2T-12G18G-45-R-SFF-10W is an independently controlled, high power, reflective single pole two throw switch designed to operate between 12.0 to 18.0 GHz and handle input power levels up to 10 W CW and 30 W peak with a maximum pulse width of 1usec and maximum PRF of 2 MHz.

PMI Model No. DTA-0R5G18G-60-CD-1 is a non-reflective, 10 bit, programmable 60 dB pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 0.5 to 18.0 GHz.

PMI Model No. LM-0518-10-1W-SHS-2-M-1218 is a high power limiter that operates from 12.0 to 18.0GHz.  This limiter handles 100 W peak power with a pulse width of 1usec.  The insertion loss is only 1.5dB typically and has a VSWR of 2.0:1 maximum.

PFEM-9D4G-CD-1 is a multi-function module that provides amplification, switching and filtering within the frequency band of 9410 MHz.  This module provides two input channels and is switchable to a common output.  This model is designed to offer multiple gain level selection, high channel to channel isolation and fast switching speeds.

PMI Model No. P2T-1G18G-10-R-5V-SFF-HIP10W-HERM is a hermetically sealed, reflective, single pole, two throw pin diode switch that operates over the 1.0 to 18.0GHz frequency range.  This model is capable of handling an input power level of 5 WCW while providing switching speeds of less than 40ns typically.

PMI Model No: SDLVA-3G18G-CW-70-MAH is a CW-immune successive detection log video amplifier operating in the 2.0 to 18.0 GHz frequency band.  It features an SPST on the RF output which allows for the RF to be blanked when the RF input signal is below the -64 dBm threshold.

PMI Model No. PEC3-40-1D6G2D7G-15LM-SFF is a limiting amplifier that operates over the frequency range of 1.6 to 2.7 GHz and offers a limited output of 15 dBm  ± 2 dBm.  The saturated power frequency flatness is ±1.5 dB maximum with a gain of 35 dB minimum and a typical noise figure of 4.5 dB.  The 2nd harmonic rejection is 24 dBc typically with an OIP3 of +18 dBm typical.

PMI Model No. P8T-2G6G-90-T-55-SFF is a high speed, single pole, eight throw, absorptive switch that operates over the frequency range of 2.0 to 6.0 GHz.  This switch offers very-high isolation of 97 dB typical while maintaining a typical fast switching speed of 30 ns.  The operating input power rating is +23 dBm CW with an insertion loss of 3.5 dB.

PMI Model No. LM-18G40G-18-1W-292FF is an ultra-high speed, millimeter wave, high power RF limiter that operates over the frequency range of 18.0 to 40.0 GHz.  This limiter can handle input power levels up to 1 W CW and provides a leakage output power of +18 dBm maximum and +12 dBm typical.

PMI Model No. PSD-2G6G-CD-1 is high power, switch box assembly that provides protection to front-end receivers when in the presence of high power signals.  This is accomplished by sensing the input signal level and then switching the input signal into 50 ohms terminations when a set threshold level is exceeded.  This assembly operates from 2.0 to 6.0 GHz and can handle input power levels up to 10 W CW.

PMI Model No. PS-360-3237-8-292FF is a high speed, millimeter wave, 8-bit digitally controlled, phase shifter that operates over the frequency range of 32.0 to 37.0 GHz.  This phase shifter offers a low insertion loss of 13 dB typically and maintains a VSWR of 1.8:1.  The total phase shift range is 358.593° having a step size of 1.406° and switches between states in less than 500 ns.

PMI Model No. POB-16-48-22-LCA is a 4.0 to 8.0 GHz low noise amplifier which provides 16 dB of gain while maintaining a gain flatness of ±1.0 dB typically over the operating frequency. The noise figure is 3 dB typical and offers a typical OP1 dB of +22 dBm. The amplifier requires +12 to +15 VDC and the current draw is 225 mA typical.

PMI Model No. PSD-6G16G-CD-1 is high power, switch box assembly that provides protection to front-end receivers when in the presence of high power signals.  This is accomplished by sensing the input signal level and then switching the input signal into 50 ohms terminations when a set threshold level is exceeded.  This assembly operates from 6.0 to 18.0 GHz and can handle input power levels up to 10 W CW.

PMI Model No. PE2-25-218-20-12-SFF is a 2.0 to 18.0 GHz low noise amplifier that provides greater than 25 dB of gain while maintaining a maximum gain flatness of ±1.5 dB maximum over the operating frequency.  The noise figure is 4.5 dB typical and offers an OP1dB of +20 dBm minimum.  The operating voltage is +12 to 15 VDC and the current draw is 300 mA maximum.

Model 7CL5125-1490-CD-SFF is a band pass filter centered at 5125MHz and has a nominal bandwidth of 1490MHz.  This filter provides over 40dB of rejection between 3.0 to 3.658GHz and between 6.65 to 7.3GHz and over 65dBc of rejection between 1.5 to 2.5GHz.

PMI Model No. P4T-100M40G-90-T-512-292FF-SP is a 100 MHz to 40 GHz, ultra-compact, high speed, single pole, four throw, absorptive switch.  This switch offers over 100 dB of port to port isolation from 100 MHz to 18 GHz, over 90 dB from 18 to 26.5 GHz and over 75 dB from 26.5 to 40 GHz.

PMI Model No. PE2-35-1R02R0-1R4-17-12-SFF is a low noise amplifier that operates over the 1.0 to 2.0 GHz frequency range.  This model provides 35 dB of gain and offers a low noise figure of 1.4 dB typically.  The amplifier provides an OP1 dB is +17 dBm and operates on +12 to +15VDC with 160 mA of typical current draw.

PMI Model No. PEC3-40-30M26R5G-6R0-12-12-SFF is a 30 MHz to 26.5 GHz low noise amplifier that provides greater than 35 dB of gain while maintaining a maximum gain flatness of ±3.5dB maximum over the operating frequency.  The noise figure is 6.0 dB typical and offers an OP1dB of +12 dBm minimum.  The operating voltage is +12 to 15 VDC and the current draw is 700 mA maximum.

PMI Model No. PEC-37-9G10G-3R0-27-SFF is a low noise amplifier that operates over the 9.0 to 10.0 GHz frequency range.  This model provides 28 dB of gain and offers a low noise figure of 3.0 dB maximum.  The amplifier provides an OP1 dB is +27 dBm minimum and operates on +10 to +15 VDC with 400 mA of typical current draw.

PMI Model PS-180-4R15R3-SFF is a 0 /180 degrees, bi-phase modulator designed to operate over the 4.1 to 5.3 GHz frequency range.  This model can handle RF input signal levels up to +30 dBm without damage; has an insertion loss of 3.0 dB maximum and a maximum VSWR of 1.7:1.  A TTL control will switch between 0 degrees and 180 degrees phase states in less than 100 nsec.  The required supply voltages are ±5 VDC.

PMI Model No. PUB-15-500M20G-20-LCA is a 500 MHz to 20.0 GHz low noise amplifier which provides 15 db of gain while maintaining a gain flatness of ±1.75 db typically over the operating frequency.  The noise figure is 3 dB typical and offers a typical OP1 dB of +20 dBm.  The amplifier requires +12 to +15 VDC and the current draw is 225 mA typical.

PMI model SDLVA-315M362M successive detection log video amplifiers (SDLVA) offers 65 dB dynamic range over the frequency range of 315 to 362 MHz.  This model offers a fast rise time of 35 nsec maximum and a recovery time of less than 500 nsec.  The unit is temperature compensated such that log accuracy over temperature remains less than +/-2.5 dB over the full operating temperature range of -33° to +77° C.

PMI model SDLVA-250M6G-CD-1 successive detection log video amplifiers (SDLVA) offers 70 dB dynamic range over the frequency range of 0.25 to 6.0 GHz.  This model offers an ultra-fast rise time of 10nsec maximum and a recovery time of less than 60 nsec. The unit is temperature compensated such that log linearity over temperature remains less than +/-2.5 dB over the full operating temperature range of -40 to +70 C.

PMI Model SDLVA-500M4G-CD-1 successive detection log video amplifiers (SDLVA) offers 70 dB dynamic range over the frequency range of 0.5 to 4.0 GHz.  This model offers an ultra-fast rise time of 10 nsec maximum, a recovery time of less than 60 nsec and a limited RF Output of +7 dBm. 

PMI Model No. PEC-85-0R32R5-15LM-12-SFF is a limiting amplifier that operates over the frequency range of 300 MHz to 2.5 GHz. This model provides a gain of 85 dB typically and a limited output of +15 dBm ± 2.5 dBm.

PMI Model No. PE2-1020-R518-12-SFF is a low noise amplifier that offers a positive gain slope versus frequency. This type of amplifier is useful when trying to equalize frequency flatness over a broad bandwidth. This model provides 10 dB of gain at 500 MHz and 20 dB of gain at 18 GHz.

PMI Model No. PBB-20-218-16-LCA is a 2.0 to 18.0 GHz low noise amplifier which provides 20 dB of gain while maintaining a gain flatness of ±2.0 dB maximum over the operating frequency. The noise figure is 4 dB typical and offers a typical OP 1 dB of +14 dBm minimum.

PMI amplifier Model PEC-38-30M18G-12-SFF is a broadband, low noise amplifier that operates over the 30 MHz to 18 GHz frequency range.  This model provides 38 dB of gain and has a gain flatness of ±2.0 dB maximum.

PMI Model No. PEC3-33-218-20-15-SFF-HS-E is a 2.0 to 18.0 GHz low noise amplifier that provides greater than 33 dB of gain while maintaining a maximum gain flatness of ±2.0 dB maximum over the operating frequency.  The noise figure is 4 dB typical and offers an OP1 dB of +20 dBm minimum and an OIP3 of +30 dBm typical.  The operating voltage is +15 VDC and the current draw is typically 350 mA.

Model LM-26G40G-14-20W-292MM is a high power limiter capable of withstanding an input power level of 20 W, 440 to 670 nsec pulse width, PRF 600 to 900 kHz, 40% duty cycle.  This model operates in the 26.5 to 40 GHz frequency range.  The insertion loss is 4.0 dB maximum, VSWR of 2.0:1 and 250 nsec response time and a typical leakage of +14 dBm.

PMI Model No. P4T-100M2G-50-T-SFF-IN is an absorptive, single pole, four throw solid-state switch that operates over the 100 MHz to 2.0 GHz frequency range.  The insertion loss is less than 3 dB and offers port to port isolation of over 50 dB.  The switching speed is 25 nsec maximum and the rise and fall times are less than 10 nsec.

PMI Model CDT-2M18-30-BB Options DE, D is a threshold detector that operates over the 2 MHz to 18 GHz frequency range.  This model has a low insertion loss of 2.5 dB maximum and operates over an input power range of -30 to 0 dBm.  The threshold level is adjustable and the output signal is TTL positive logic.

PMI Model No. PS-500M2G-8B-SFF is a State-Of-The-Art, 8-bit digitally controlled phase shifter that operates over the 500 MHz to 2.0 GHz frequency range.  This model has a typical insertion loss of 10 dB and offers 360 degrees of phase shift via 8-bit TTL control.

PMI Model No. P4T-10G40G-60-T-GPO is a single pole, four throw, absorptive, solid-state switch that operated over the frequency range of 10 to 40 GHz.  This model provides over 60 dB of isolation and has an insertion loss of 6 dB maximum.  The VSWR is better than 2.0:1 into 50 ohm impedance.

PMI Model No. PE2-30-218-4R0-20-12-SFF-BT is a 2.0 to 18.0GHz low noise amplifier that has an integrated bias-tee network on the output port. This amplifier provides 30 dB of gain while maintaining a maximum gain flatness of ±2.0 dB max over the operating frequency.

PMI Model No. PUB-14-30M20G-14-LCA is a 30 MHz to 20.0 GHz low noise amplifier which provides 14 dB of gain while maintaining a gain flatness of ±1.2 dB typically over the operating frequency. The noise figure is 3 dB typical and offers an OP1 dB of +14 dBm typical.

PMI Model Number LM-30M3G-C3-1 is a high power limiter that operates from 30 MHz to 3.0 GHz. This limiter can handle input power levels up to 5 W CW and provides a maximum leakage of +10 dBm. The insertion loss is 1.2 dB maximum with a maximum VSWR of 1.5:1. The recovery time is less than 1 usec.

PMI Model No. PUB-15-30M20G-20-LCA is a 30MHz to 20.0GHz low noise amplifier which provides 15 dB of gain while maintaining a gain flatness of ±2.5 dB typically over the operating frequency. The noise figure is 3 dB typical and offers a typical OP1 dB of +20 dBm. The amplifier requires +12 to +15 VDC and the current draw is 225 mA typical.

The PS-360-DC-IR-9G10G is a 10-Bit digitally controlled 360 degree phase shifter that operates from 9.0 to 10.0 GHz. This model offers low insertion loss of 7.5 dB and a phase shift accuracy of ±0.6 degrees typically.

Model SDLVA-0R71R3-75-CD-3 is a successive detection log video amplifier that operates over the 700 to 1300 MHz frequency range. This model has a Dynamic Range of 75 dB, a log slope of 40 mV/dB.  The log linearity is ±1.2 dB typical from -65 to +5 dBm input power levels and a typical TSS of -70 dBm.

Model SDLVA-0R71R3-75-CD-1 is a successive detection log video amplifier that operates over the 700 to 1300 MHz frequency range. This model has a dynamic range of 75 dB, a log slope of 40 mV/dB and a nominal video bandwidth of 20 MHz. This model offers very fast rise times of 9 nsec and fall times of 25 nsec typically.

PMI Model No. P4T-10G40G-60-T-GPO is a single pole, four throw, absorptive, solid-state switch that operated over the frequency range of 10 to 40 GHz. This model provides over 60 dB of isolation and has an insertion loss of 6 dB maximum. The VSWR is better than 2.0:1 into 50 ohm impedance.

PMI Model No. P1T-26D532D5-90-1212-292FF is an absorptive, single pole, single throw, solid-state switch that operates over the frequency range of 26.5 to 32.5 GHz. This model provides a minimum isolation of 90 dB and maintains low insertion loss of 5.0 dB maximum. The VSWR is 2.0:1 maximum into 50 ohms impedance and offers switching speeds of 25 nsec maximum and 15 nsec typical.

PMI Model LM-6D7G7D9G-30W-SFF is a RF limiter that operates in the 6.7 to 7.9 GHz frequency range. This limiter can handle 30 W CW input power and provides a maximum leakage of +18 dBm. This model has a low insertion loss of 1.1 dB maximum and a recovery time of 10 usec maximum.

PMI Model No. PS-360-900M930M-6-SFF is a 900 to 930 MHz, 6-BIT digitally controlled phase shifter having a LSB of 5.6 degrees. The insertion loss is 7 dB typical, 7.5 dB maximum with a typical VSWR of 2.0:1. This is a high speed phase shifter that can switch from one phase state to the next in typically 250 nsec.

PMI Model No. PE2-28-20R040R0-5R5-18-12-SFF is a 20 to 40GHz low noise amplifier that typically provides 28 dB of gain. The gain flatness is ±2.5 dB maximum and ±1.5 dB typical with a noise figure is 5.5 dB typical. This amplifier provides a minimum OP1 dB of +15 dBm minimum.

PMI Model No. PE2-30-0R56R0-5R0-22-12-SFF is a 500 MHz to 6.0 GHz low noise amplifier that typically provides 30 dB of gain. The gain flatness is ±1.0 dB maximum with a noise figure is 5.0 dB typical. This amplifier provides a minimum OP1 dB of +21 dBm.

PMI Model No. PEC2-60-4G8G-1R75-14-12-SFF is a 4 to 8 GHz low noise amplifier that typically provides 60 dB of gain. The gain flatness is ±1.25 dB maximum with a noise figure is 1.75 dB maximum. This amplifier provides a minimum OP1 dB of +14 dBm.

PMI Model No. PIA-10G-CD-1 is a 10 GHz integrated, dielectric resonator (DRO) module with three outputs, each having a 0 to 360 degree analog controlled, variable phase shifter and 0 to 10 dB analog controlled, variable output control capability on each of the outputs.  This model provides a low harmonic output of -50 dBc typical and an output power level of +19 dBm typical.  

PMI Model No. FD-0518-10-812 is a 8.0 to 12.0 GHz frequency discriminator that provides a video output of 50 mV/GHz and has an accuracy of +/-200 MHz. The rise time is less than 20 nsec and operates into a 100 ohm video load. This model operates on +/-15 VDC and measures 2.0" x 1.8" x 0.5".

PMI Model BPF1370-50-CD-TNCMF is a band pass filter with a center frequency of 1370 MHz and a 1dB bandwidth of 50 MHz. This filter provides an ultimate stop-band rejection of 60 dBc and is rated to handle an input signal level of 6 W, 10% duty factor. This model offers low loss of less than 3 dB and is supplied in a package measuring 2.6" x 1.0" x 0.75".

PMI Model BRF1370-50-CD-TNCFF is a band reject filter with center frequency of 1370 MHz and a notch bandwidth of 60 MHz with a notch depth is 50 dB. This filter is rated to handle 10 W and is supplied with TNC connectors. The package measures 2.6" x 1.0" x 0.75".

PMI Model No. P2T-14D415D4-15-SMT-20W is a driverless high-power SP2T switch in a compact package designed for surface mount applications. This switch operates from 14.4 to 15.4 GHz and has an insertion loss of 1.2 dB maximum at +25° C.

PMI Model PSAT-2500-11B-CD-1 is a 2.5GHz, 11 Bit Digitally Controlled Attenuator / Analog Phase Shifter assembly having the capability for phase shifting from 0 to 360° with an attenuation range of 60 dB minimum. This model has insertion loss of 10 dB maximum and a VSWR of 1.5:1 maximum into 50 ohms.

PMI Model No. DTO-2G18G-CD-1 is a digitally controlled oscillator (DTO) covering the frequency range of 2 to 18 GHz. This model is designed to withstand stringent military ground or airborne environments.

PMI Model PLVA-500M18G-50 is a 50 dB detector log video amplifier designed to operate over the 500 MHz to 18.0 GHz frequency range. This model employs planar diode detectors and integrated video circuitry for high speed performance and outstanding reliability.

PMI Model No. P4T-4G12G-35-R-SFF-PM is a single pole, four throw, reflective switch that operates over the 4.0 to 12.0 GHz frequency range. This model features low insertion loss of 1.0 dB typical and isolation of 70 dB typical. All ports are phase matched to be within ±7.5 degrees.

PMI Model No.P2T-14D415D4-15-SMT-20W is a driverless high-power SP2T switch in a compact package designed for surface mount applications. This switch operates from 14.4 to 15.4 GHz and has an insertion loss of 0.5 dB maximum. The Tx/Rx isolation is 15 dB minimum and this switch can handle input power levels up to 20 watts. The size of this SMT switch is 0.35" x 0.5" x 0.21".

PMI Model BRF17D6G-20M-CD-1 is a band reject "notch" filter having a pass band of DC to 17.47GHz and 17.77 to 20 GHz and over 40 dB of rejection at 17.59 to 17.61 GHz. Insertion loss in the pass band is less than 5 dB and VSWR is better than 2.0:1. This filter is supplied with SMA female connectors and the size is 1.5" x 0.5" x 0.68".

PMI Model Number PS-360-8D5G11G-8-SFF-LVT is an 8.5 to 11 GHz, 8 Bit digitally controlled phase shifter with capability of phase shift ranges from 0 to 360 degrees. The phase shift resolution is 1.41 degrees and controlled by eight, low voltage TTL control lines. This model has a typical insertion loss of 8 dB and phase accuracy of ±8.5 degrees.

Planar Monolithics Industries, Inc. introduces new USB style RF & microwave control components and LNA's to 40 GHz. RF & microwave USB style components & LNA’s featuring: 50 MHz to 40 GHz low noise amplifier, 500 MHz to 40 GHz SPDT absorptive switch, and 100 MHz to 40 GHz variable attenuator.

PMI Model No. PS-360-2433D5-6-SFF-1 is a 2433.5MHz ±1MHz, 6-BIT digitally controlled phase shifter that offers up to 360 degrees of phase shift range with a phase accuracy of ±8 degrees typical. This model has a LSB of 5.6 degrees and a low insertion loss of 5 dB typically.

Model No.: TD-16G40G-20-292F is a high speed threshold detector designed to operate over the 16 to 40 GHz frequency range, with an adjustable threshold level of -20 to 0 dBm, and VSWR of 2.5:1maximum.

PMI Model 7SFB-950M18G-CD-SFF is an eight channel switched filter bank that covers pass-band frequencies of 950 MHz to 18.05 GHz. This filter bank offers 7 different pass-bands throughout the operating frequency which can be selected via a 3-bit decoded TTL signal.

PMI Model No.PEC-9R510R7-100W-SFF-SPDT is a high power, single pole, double throw switch capable of handling 120 W CW. This solid-state switch operates in the frequency range of 9.5 to 10.7 GHz and has a typical insertion loss of 1.5 dB and port to port isolation of over 40 dB.

PMI Model No. BR1050-300-CD-TNC-MF is a band reject filter that offers a pass band of DC to 18.0 GHz having 50 dB of rejection from 900 to 1200 MHz. This filter has only 1.5 dB of loss and a VSWR of 2.0:1 maximum. This filter can handle input power levels up to 5 W.

PMI Model P4T-0R1G20G-100-T-SFF is a single pole, four throw, solid-state absorptive switch which operates over the 100 MHz to 20.0 GHz frequency range. This model provides 110 dB of isolation over the entire frequency range of operation and offers low insertion loss performance with fast switching speeds.

Model TD-30T-218-FC-HS Option 220 is a high speed threshold detector designed to operate over the 2 to 20 GHz frequency range. It has as external adjustment to vary the threshold level from -10 to -20 dBm, with an input flatness of typically ±1.0 dB and a VSWR of less than 3.0:1.

Model BPM-1G2G-1-SFF is a bi-phase modulator designed to operate over the 1.0 to 2.0 GHz frequency range. This model can handle RF input signal levels up to -3 dBm and has an insertion loss of 8.8 dB maximum.

PMI Model No. PE2-4020-9R510R7-2R5-12-12-SFF-VVG is a voltage variable gain, low-noise amplifier that operates over the 9.5 to 10.7 GHz frequency range. This model provides 40 dB of small signal gain with a typical noise figure of 4.0 dB and an OP1dB of +12 dBm.

PMI Model No. P2T-500M20G-50-T-512-SFF-I-NH is a terminated single pole, two throw switch that operates from 500 MHz to 20 GHz which handles +23 dBm CW input power. The port to port isolation is 50 dB minimum, Insertion loss of 2.8 dB maximum and has a maximum switching speed of 50 nsec.

PMI Model PSM-50M1G-CD-1 is a single sideband modulator that operates over the 50 MHz to 1.0 GHz frequency range. The input P1dB is +5 dBm typical and has an IF Modulation Range of DC to 10 MHz. The IF Modulation Power Range is +7 dBm minimum and +13 dBm maximum into 50 ohms.

PMI Model PTB-42-1G40G-12-292FF-DC12 is a portable amplifier that operates over the 1.0 to 40.0GHz frequency range. This model provides 40dB of typical gain with an OP1dB of +22dBm typical (1-18GHz) and +18dBm typical (18-40GHz).

PMI Model Number PVVAN-0R4G6G-40-MP-1 is a non-reflective, linearized, voltage controlled pin diode attenuator. This model operates over the 400 MHz to 6.0 GHz frequency range and provides up to 40 dB of attenuation range from 0 to +10 VDC control voltage. Typical insertion loss is 2.8 dB with a typical speed of 1 usec.

PMI Model Number PS-360-2D4G2D5G-10-CD-SFF is a 2.4 GHz to 2.5 GHz, 10-Bit digitally controlled phase shifter that offers up to 360 degrees of phase shift range. This model has a LSB of 0.36 degrees and a low insertion loss of 4.0 dB typically.

The model TDCS-4T-10F-HP is an integrated threshold detector, 17 dB coupler and SPDT PIN diode switch. This device operates from 9 to 10.5 GHz (other frequency ranges are also available), with an insertion loss of 2 dB maximum, VSWR of 1.5 maximum, 2 W average RF input power handling capability and TTL threshold output.

The model QC-052-YR3 is a 3 dB quadrature hybrid that when a signal is applied to any port the hybrid will split that signal equally between the ports on the side away from the input with the port adjacent to and on the same side as the input port remaining isolated.

Planar Monolithics Industries, Inc. (PMI) is very proud to announce the development of an Ultra-Broadband Threshold Detector which operates from 2 MHz to 18.0 GHz. The VSWR is 1.9:1 Max. and the Thru Path Insertion Loss is 2.5dB Max. The Dynamic Range is -30 to 0 dBm with a 10kHz Video Bandwidth.

The model RMR-818-77-NRL is an 8 to 18 GHz radar/microwave monitoring receiver de-signed for laboratory applications. The receiver uses an extended range detector log video amplifier (DLVA), a pre-amplifier and RF bandpass filtering. It also offers a dynamic range of 75 dB with a typical TSS of -80 dBm.

Planar Monolithics Industries offers the Detection Preamp Module, Model Number ADP-140M-51DR-TD with Options HS, NRL, LOG, which Provides Amplification, Video Detection, and Video Amplification with an Input of 130 MHz Pulsed RF with a 25 MHz Bandwidth.The Size is 3.50”(L) X 3.00”(W) X 0.50”(H).

Planar Monolithics Industries Model No: SDLVA-61F-80-582987-004 Option TBRK, MS is a matched set of successive detection log video amplifiers in a compact stacked configuration. This unit operates over 61.25 MHz ± 250 KHz with a transfer function of E – 22.5 PIN+ 200, where PIN is the input power in dB above -80 dBm and E = output voltage in millivolts.

Planar Monolithics Industries Inc. is pleased to announce the development of it’s new 0.4 to 16 GHz 2 way power divider, model number: APD-2-0416-YR1. The insertion loss from 0.4 to 6 GHz and 6 to 16 GHz are 1.8 dB max and 4.0 dB max, respectively.

Planar Monolithics Industries Model No: TD-30T-914-DX is a High Speed Threshold Detector Designed to Operate over the 9 to 14 GHz Frequency Range, with an Adjustable Threshold Level of -18 dBm to +5 dBm, and a Typical VSWR of 2.0:1 (2.5:1 Maximum).

Planar Monolithics Industries, Inc. has developed the PMI Model No.: TD-30T-SHS-218-30DBAMP Options DAC, DS, an Ultra-High Speed, High Sensitivity Threshold Detector designed for Broad Band Applications in the 2 to 18 GHz Frequency Range and with an 8 Bit Digital Control.

Planar Monolithics Industries Inc. is pleased to announce the development of it’s new 8 to 11GHz 10 dB directional coupler with field replaceable SMA connectors, model number: RFOC-811-QRC-dc-10. By using the technology of microstrip line to strip line transitions, all the feed thrust of input and output ports can be soldered directly to the mechanical housing to have better mechanical support.

Planar Monolithics Industries Model No: PS-90-8018 Option 812, HS15NS is a high speed 0 to 180 degree, miniature, bi-phase modulator / phase shifter with TTL control logic (ECL logic available). This high speed model has 15 nS delay on/off and operates between 8 to 12 GHz.

Planar Monolithics Idustries Inc. is pleased to announce the development of it’s new 0.5 to 18 GHz 2 way power divider, model number: APD-2-0518-YR1. The insertion loss and isolation from 0.5 to 8 GHz and 8 to 18 GHz are 1.8 dB max, 16.5 dB min and 3.5 dB max, 21 dB min, respectively.

Planar Monolithics Industries, Inc is pleased to offer our latest development: Model RFE-218-70-BB which is a 2.0 to 18.0 GHz direction finding receiver frontend.The minimum dynamic range of the subsystem is -60 to +5 dBm; while the Input VSWR in frequency range is 3.0:1 and the frequency flatness at the outputs is ±3.0 dB maximum.

Planar Monolithics Industries, Inc. (PMI) is very proud to offer our Model ADP-2-218-M-BB Miniature Power Divider.This Power Divider is designed to operate from 2.0 to 18.0 GHz, with an Insertion Loss of only 2.2dB Maximum, Isolation of 16.0 dB Minimum and a VSWR of 2.0:1 Maximum.

PLANAR MONOLITHICS INDUSTRIES, INC. has developed the PMI Model No: MSDLVA-2020-70 OPTIONS 48 & SE SDLVA’S that operate from 4 to 8 Ghz (other frequencies are available). This unit has high speed and uses GaAs technology in a compact size. The dynamic range is 80 dB. The VSWR is 1.6:1 typical. The TSS is -73 dBm typical.

PMI would like to announce its newest solid-state switch that offers a level of performance exceeding industry standards. PMI Model No. P4T-500M40G-60-T-55-292FF is an absorptive, solid-state switch that covers the 500 MHz to 40 GHz frequency range. This model offers extremely low insertion loss, very high isolation and a typical switching speed of 27 nsec.

PMI Model SDLVA-218-71-70MV is a CW Immune, Extended Range Detection Log Video Amplifier (ERDLVA) which offers 71 dB dynamic range over the frequency range of 2.0 to 18.0 GHz. This model offers a maximum rise time of 35 nsec and a recovery time of less than 350 nsec. CW immunity is provided for signal levels up to -40 dBm.

PMI Model No. PEC-2D35G-100W-SFF-SPDT is a solid-state switch capable of hot switching over 100 W of input power. Most high power switches are not of a solid-state design and do not offer the benefit of fast switching speeds. PMI has developed a unique design that offers fast switching speeds as well as the added reliability of solid-state devices.

PMI Model No. P1T-18G40G-90-1515-292FF is a solid-state single pole, single throw switch that operates over the 18.0 to 40.0GHz frequency range. This model offers ULTRA-HIGH Isolation measuring greater than 90 dB while maintaining a low insertion loss of 5.0 dB maximum.

Model SDLVA-6G18G-CD-1 Successive Detection Log Video Amplifiers (SDLVA) offers 75 dB Dynamic Range over the frequency range of 6.0 to 18.0GHz. This model offers an ultra-fast rise time of 10nsec maximum and a recovery time of less than 60nsec. The unit is temperature compensated such that log linearity over temperature remains less than +/-2.5dB.

Model LM-35D5G-14-20W-292FF is a high power limiter capable of withstanding an input power level of 20 W, 440 to 670 nsec Pulse Width, PRF 600 to 900kHz, 40% Duty Cycle. This model operates in the 35 to 36GHz frequency range, but can be used over the 24.5 to 38GHz frequency range with degraded performance. The insertion loss is 3.0 dB maximum, VSWR of 2.0:1 and 250 nsec response time packaged in a small 0.50 X 0.50 X 0.22 housing.

PMI Amplifier Model PEC-42-1G40G-20-12-292MM is an ultra-broadband, low noise amplifier that covers the 1.0 to 40.0 GHz frequency range. This model provides a flat gain response while maintaining a typical output power of +20 dBm. [Other specifications available upon request.]

PMI Model SDLVA-218-71-70MV is a CW Immune, Extended Range Detection Log Video Amplifier (ERDLVA) which offers 71 dB Dynamic Range over the frequency range of 2.0 to 18.0 GHz. This model offers a maximum rise time of 35 nsec and a recovery time of less than 350 nsec.

Model Number PS-360-3237-5-292FF is a 32 to 37 GHz Digitally Controlled Phase Shifter with Capability for Phase Shifting from 0 to 349°. 5 Logic Lines allow various phase shift with a LSB of 11.25°.

PMI would like to announce its newest solid-state switch that offers a level of performance exceeding industry standards. PMI Model No. P16T-0R5G18G-60-T-SFF is an absorptive, solid-state switch that covers the 500 MHz to 18 GHz frequency range.

PMI would like to announce its newest solid-state switch that offers a level of performance exceeding industry standards. PMI Model No. P2T-100M1G-90-T-55-SFF is an absorptive, SP2T solid-state switch that covers the 100MHz to 1.0GHz frequency range. This model offers extremely low insertion loss, very high isolation and a switching speed of 50nsec maximum.

PMI would like to announce its newest solid-state switch that offers a level of performance exceeding industry standards. PMI Model No. P5T-100M1G-90-T-55-SFF is an absorptive, SP5T solid-state switch that covers the 100MHz to 1.0GHz frequency range. This model offers extremely low insertion loss with very high isolation.

PMI would like to announce its newest solid-state switch that offers a level of performance exceeding industry standards. PMI Model No. P2T-8G11G-90-T-SFF is an absorptive, SP2T solid-state switch that covers the 8.0GHz to 11.0GHz frequency range. This model offers extremely low insertion loss, very high isolation and a switching speed of 50nsec maximum.

PMI would like to announce its newest product line addition of digitally tuned oscillators (DTO). They now offer a full line of digitally tuned oscillators (DTO) covering various frequencies in the 500 MHz to 18 GHz range.

PMI Model ERDLVA-218-CW-LPD is a CW Immune, Extended Range Detector Logarithmic Video Amplifier (ERDLVA) designed for ultra low DC power consumption. This model operates over the 2 to 18 GHz frequency range and has the ability to interface with an output cable measuring over 100 feet in length.

Model PEC3-40-2G6G-15LM-SFF-HS is a temperature compensated, limiting amplifier that operates over the 1.85 to 6.25 GHz frequency range and provides a limited power output of +15 dBm minimum for an input power range of -15 to +17 dBm.

PMI Model No. P8T-0R1G20G-110-T-512-SFF is a high speed, single pole, eight throw, absorptive switch capable of switching within 300 nsec.  The frequency range is 0.1 to 20.0 GHz and has over 110 dB of isolation.

PMI Model P2T-18G40G-65-R-292FF is a single pole, two throw, solid-state switch which operates over the 18 to 40 GHz frequency range. This model provides 55 dB of isolation over the entire frequency range of operation and offers low insertion loss performance with fast switching speeds.