advertisment Advertisement
advertisment Advertisement
advertisment Advertisement
advertisment Advertisement

Planar Monolithics Industries Inc.

Company Profile

Planar Monolithics

Contact Information

Phone: (301) 662-5019
Fax: (301) 662-1731

Location

Planar Monolithics Industries Inc.
7311-F Grove Road
Frederick MD 21704
United States
PMI is a leading manufacturer of RF/Microwave components and Integrated RF Assemblies, Including: Amplifiers, Variable Solid-State Attenuators, Limiters, Detectors, Detector Log Video Amplifiers, Solid-State Switches & Switch Matrices, Phase Shifters, Filters & Switch Filter Banks, Couplers, Dividers and more up to 40GHz for commercial and defense applications.

Products

Ethernet Microcontroller Test Box: PL-MCU-ENET-TTL-MAH

July 17, 2014

EthernetMicroTestBoxPMI Model No. PL-MCU-ENET-TTL-MAH is an ethernet microcontroller test box which allows for an ethernet command to be sent up to 18 parallel TTL output bits.  This controller can be used with many PMI products that require parallel digital commands, such as switches, attenuators, phase shifters and IQ modulators.

Read More

Low Noise Amplifier: PE2-30-2R04R0-1R5-21-12-SFF

July 03, 2014

PE2-30-2R04R0-1R5-21-12-SFFPMI Model No. PE2-30-2R04R0-1R5-21-12-SFF is a 2.0 to 4.0 GHz, low noise amplifier that typically provides 30 dB of gain while maintaining a maximum gain flatness of +/-1.0 dB over the operating frequency.  The typical noise figure is 1.5 dB and offers a minimum OP1 dB of +21 dBm.  The amplifier requires +12 to +15 VDC and has a nominal current draw of 300 mA.

Read More

Low Noise Amplifier: PE2-30-2R04R0-1R5-21-8V-SFF

July 03, 2014

PE2-30-2R04R0-1R5-21-8V-SFFPMI Model No. PE2-30-2R04R0-1R5-21-8V-SFF is a 2.0 to 4.0 GHz, low noise amplifier that typically provides 30 dB of gain while maintaining a maximum gain flatness of +/-1.0 dB over the operating frequency.  The typical noise figure is 1.5 dB and offers a minimum OP1 dB of +21 dBm.  The amplifier requires +8 VDC and has a nominal current draw of 300 mA.

Read More

Phase Locked Oscillator: PLO-9G-CD-1

July 03, 2014

PLO-9G-CD-1PMI Model No. PLO-9G-CD-1 is a phase locked oscillator with an output frequency of 9.0 GHz.  This model provides minimum output power of +21 dB with all spurs held to -60 dBc and harmonics held to -25 dBc. The unit has a VSWR or <1.5:1 for all phases and is supplied with SMA(F) connectors in a housing that measures 2.25" x 2.25" x 0.63"

Read More

Sinewave Crystal Controlled Oscillator: PXO-100M-CD-1

July 03, 2014

PXO-100M-CD-1PMI Model No. PXO-100M-CD-1 is a 100 MHz, sinewave crystal controlled oscillator with coaxial output connector.  This model provides minimum output power of +7 dBm with all spurs held to -60 dBC (10 to 500 MHz) and harmonics and sub-harmonics held to -40 dBc.  It requires DC power of +15 V ±5% 40 mA max and is in a housing that measures 2.0 " 2.0" x 0.75".

Read More

SP9T Reflective Switch: P9T-500M40G-60-R-55-292FF-OPT1222

July 03, 2014

P9T-500M40G-60-R-55-292FF-OPT1222PMI Model No. P9T-500M40G-60-R-55-292FF-OPT1222 is a high speed, single pole, nine throw, reflective switch capable of switching within 100 ns.  The frequency range is 0.5 to 40 GHz (-OPT1222 is optimized over 12.0 to 22.0 GHz) and it has over 60 dB of isolation.

Read More

Variable Gain Amplifier: PE2-34-2G18G-3R5-15-SFF-VVG-DD

July 03, 2014

PE2-34-2G18G-3R5-15-SFF-VVG-DDPMI Model No. PE2-34-2G18G-3R5-15-SFF-VVG-DD is a voltage variable gain amplifier with integrated diode detector operating over the frequency range of 2.0 to 18.0 GHz.  This amplifier is supplied in our standard PE2 housing that can be used as SMA connectorized or as a surface mount component.  It is optimized for 5.5 to 18.0 GHz. 

Read More

Reflective Switch: P2T-1G1R1G-25-R-SFF-100W

May 27, 2014

P2T-1G1R1G-25-R-SFF-100WPMI Model No. P2T-1G1R1G-25-R-SFF-100W is a single pole, two throw, hermetically sealed reflective switch designed to operate over the 1.0 to 1.1 GHz frequency range.  This model is designed to handle 100 W average input power and 5 KW peak having a 17 usec pulse width and 2% duty cycle.

Read More

Absorptive Switch: P32T-0R5G18G-60-T-SFF

May 21, 2014

P32T-0R5G18G-60-T-SFFPMI Model No. P32T-0R5G18G-60-T-SFF is a high speed, single pole, thirty-two throw, absorptive switch that operates over 500 MHz to 18.0 GHz.  This state-of-the-art switch offers top notch performance of 8.5 dB typical insertion loss and an isolation of 78 dB typically. The switch maintains 2.0:1 maximum VSWR over the full operating frequency with a maximum switching speed of 100 nsec.

Read More

Reflective Switch: P2T-1G1R1G-25-R-TFF-40W

May 02, 2014

P2T-1G1R1G...PMI Model No. P2T-1G1R1G-25-R-TFF-40W is a single pole, two throw, hermetically sealed, reflective switch designed to operate over the 1.0 to 1.1GHz frequency range.  This model is designed to handle 40 W averageinput powers and 4 KW peak having a 3 usec pulse width and 1 % duty cycle.

Read More

Digitally Controlled Phase Shifter: PS-360-DC-3 OPTION 618-15D

March 07, 2014

PS-360-DC-3OPTION618-15DPMI Model No. PS-360-DC-3 OPTION 618-15D is an 8-Bit, Digitally Controlled, 360 Degree phase shifter operating over the 6.0 to 18.0 GHz frequency range.  This unit has a typical insertion loss of 10 dB and a VWSR of 2.0:1 maximum.  The phase accuracy is ±5.2 ° with PM/AM as low as ±0.8 dB and carrier suppression of 26 dB typically. 

Read More

Programmable Attenuator: DTA-14G40G-32-CD-2

February 10, 2014

DTA-14G40G-32-CD-2PMI Model No. DTA-14G40G-32-CD-2 is a 10 Bit programmable attenuator with step resolution as low as 0.04 dB which provides over 32 dB of attenuation over the frequency range of 14.0 to 40.0 GHz.  This model is offered in a slim line housing measuring 2.0" x 1.8" x 0.5" with 2.92 mm female connectors and operates on a single +15 VDC supply with only 40 mA of current consumption typically.

Read More

Threshold Detector: TD-2G18G-RL-CD-SFF

February 10, 2014

TD-2G18G-RL-CD-SFFPMI Model No. TD-2G18G-RL-CD-SFF is a high speed threshold detector designed to operate over the 2.0 to 18.0 GHz frequency range with an adjustable threshold level of -30 to -10 dBm and a VSWR of 3.0:1 max.  This unit is supplied with field removable SMA Female connectors in a small package measuring 1.1" x 0.6" X 0.19".

Read More

Transient Switch: P4T-2G18G-60-T-512-SFF-LV

February 10, 2014

P4T-2G18G-60-T-512-SFF-LVPMI Model No. P4T-2G18G-60-T-512-SFF-LV is a 2.0 to 18.0 GHz, single pole, four throw, absorptive, low video transient switch.  This model offers 60 dB of port to port isolation and a maximum insertion loss of 3.2 dB.  It has a switching speed of 50 ns max and is independently TTL controlled with an operating power of +23 dBm CW and a VSWR of 2.0:1.

Read More

Two Throw Switch: P2T-500M18G-50-T-SFF-I

February 10, 2014

P2T-500M18G-50-T-SFF-IPMI Model No. P2T-500M18G-50-T-SFF-I is a terminated, single pole, two throw switch  that operates over the frequency range of 0.5 to 18.0 GHz.  This model handles +23 dBm CW input power with port to port isolation of 50 dB min.  It has a low insertion loss of 2.8 dB max while still offering a fast switching speed of 50 nsec max.

Read More

P8T-100M40G-85-T-512-292FF Single Pole, Absorptive Switch

February 05, 2014

P8T-100M40G-85-T-512-292FFPMI Model No. P8T-100M40G-85-T-512-292FF is a high speed, single pole, eight throw, absorptive switch operating over the frequency range of 100 MHz to 40.0GHz. It is capable of switching within 30 ns and has over 90 dB of isolation up to 18 GHz, 80 dB up to 26.5 GHz and 70 dB up to 40 GHz.

Read More

P6T-2G18G-60-T-512-SFF-LV: Transient, Solid State Switch

January 29, 2014

P6T-2G18G-60-T-512-SFF-LVPMI Model No. P6T-2G18G-60-T-512-SFF-LV is a single pole, six throw, absorptive, low video transient, solid state switch operating over the frequency range of 2.0 to 18.0 GHz.  This model has a maximum insertion loss of 4.0 dB and a minimum isolation specification of 60 dB with video transients of 2 mV typically.

Read More

PS-5G18G-400-A-SFF: Analog Phase Shifter

January 29, 2014

PS-5G18G-400-A-SFF copy (2)Model Number PS-5G18G-400-A-SFF is a 5 to 18GHz, low phase noise, analog phase shifter with capability for phase shifting from 0 to 400 degrees.  The unit operates from a single positive control voltage of 0 to +10 VDC with a phase voltage sensitivity of 40 degrees per volt. This model can be used with the SMA connectors or in a surface mount configuration.

Read More

DRO-12D3G-CD-1: Dielectrically Stabilized GaAs FET Oscillator

January 08, 2014

DRO-12D3G-DC-1PMI Model No. DRO-12D3G-CD-1 is a dielectrically stabilized GaAs FET oscillator with a center frequency of 12.3 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -75 dBc/Hz.

Read More

DRO-14D3G-CD-1: GaAs FET Oscillator

January 08, 2014

DRO-14D3G-CD-1PMI Model No. DRO-14D3G-CD-1 is a dielectrically stabilized GaAs FET oscillator with a center frequency of 14.3 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -70 dBc/Hz.

Read More

DRO-16D3G-CD-1: Stabilized GaAs FET Oscillator

January 08, 2014

DRO-16D3G-CD-1PMI Model No. DRO-16D3G-CD-1 is a dielectrically stabilized GaAs FET oscillator with a center frequency of 16.3 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -70 dBc/Hz.  The unit requires +15 VDC and 150 mA and measures 1.06" x 1.63" x 0.98".

Read More

DRO-7D7G-CD-1: Dielectrically Stabilized GaAs FET Oscillator

January 08, 2014

DRO-7D7G-CD-1PMI Model No. DRO-7D7G-CD-1 is a dielectrically stabilized GaAs FET Oscillator with a center frequency of 7.7 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -80 dBc/Hz.  The unit requires +15 VDC and 150 mA and measures 1.60" x 2.75" x 1.04".

Read More

DRO-9D7G-CD-1: GaAs FET Oscillator

January 08, 2014

DRO-9D7G-CD-1PMI Model No. DRO-9D7G-CD-1 is a dielectrically stabilized GaAs FET Oscillator with a center frequency of 9.7 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -75 dBc/Hz.  The unit requires +15 VDC and 150 mA and measures 1.35" x 1.98" x 1.04".

Read More

P2T-100M40G-95-T-512-292FF: Two Throw Pin Diode Switch

January 08, 2014

P2T-100M40G-95-T-512-292FFPMI Model No. P2T-100M40G-95-T-512-292FF is an absorptive, single pole, two throw pin diode switch that operates over the frequency range of 0.1 to 40.0 GHz.  This model incorporates a TTL compatible driver for easy system integration.

Read More

PIQ-2G18G-360-16-CD-1 I/Q Vector Modulator

January 07, 2014

PIQ-2G18G-360-16-CD-1PMI Model No. PIQ-2G18G-360-16-CD-1 is a 2.0 to 18.0 GHz, high performance I/Q Vector Modulator with 2 x 12 bit monotonic TTL compatible channels (I and Q).  This model offers a full 360 degrees of phase shift with a minimum of 16 dB of amplitude control.

Read More

DRO-11D7G-CD-1: GaAs FET Oscillator

January 01, 2014

DRO-11D7G-CD-1PMI Model No. DRO-11D7G-CD-1 is a dielectrically stabilized GaAs FET oscillator with a center frequency of 11.7 GHz.  This model provides minimum output power of +11 dBm with all spurs held to -55 dBc and harmonics held to -20 dBc. The mechanical tuning frequency is +/-25 MHz and the unit has a phase noise of -75 dBc/Hz.

Read More

DD-20-218-5PF-3-P-M High Speed Diode Detector

December 31, 2013

DD-20-218-5PF-3-P-M (1)Model Number DD-20-218-5PF-3-P-M is a high speed diode detector optimized for the 2 to 18 GHz frequency range. This model offers a fast response of 5 nsec, a TSS of -50 dBm at 2 MHz video bandwidth and a Video Capacitance of 5.6 pF. The output voltage polarity is positive, but a negative polarity is available upon request.   

Read More

PE2-30-9R010R0-2R5-21-12-SFF Low Noise Amplifier

December 31, 2013

PE2-30-9R010R0-2R5-21-12-SFFPMI Model No. PE2-30-9R010R0-2R5-21-12-SFF is a low noise amplifier that operates over the 9.0 to 10.0 GHz frequency range.  This model provides a typical gain of 30 dB while maintaining a noise figure of 2.5 dB and a OP1 dB of 21 dBm minimum.  The input and output VSWR is better than 2.0:1 and this model operates on +12 to +15 VDC.  

Read More

SDLVA-218-44-70M Detector Log Video Amplifier

December 31, 2013

SDLVA-218-44-70MVPMI Model No. SDLVA-218-44-70M is a detector log video amplifier (DLVA) designed to operate over the 2.0 to 18.0 GHz frequency range. This model offers a logging range of -40 to +4 dBm having a log slope of 70 mV/dB.  The logging linearity is better than ±0.75 dB and the rise time is 25 nsec maximum and the fall time 300 nsec maximum.  

Read More

TD-6G18G-CD-SFF High Speed Threshold Detector

December 19, 2013

TD-6G18G-CD-SFFPMI Model No. TD-6G18G-CD-SFF is a high speed threshold detector designed to operate over the 6.0 to 18.0 GHz frequency range with an adjustable threshold level of -30 to +10 dBm and aVSWR of 3.0:1 max.  The unit is supplied with removable SMA female connectors in a compact housing that measures 1.0" x 0.6" x 0.19".

Read More

PE2-28-218-5R0-12-15-SFF Low Noise Amplifier

December 17, 2013

PE2-28-218-5R0-12-15-SFFPMI Model No. PE2-28-218-5R0-12-15-SFF is a 2.0 to 18.0 GHz, low noise amplifier that provides 24 dB min of gain.  The noise figure is 4.5 dB max and offers an OP1 dB of 14 dBm min.  The operating voltage is +15 VDC and the current draw is 200 mA max.  The unit is supplied with removable SMA(F) connectors in our standard PE2 housing.

Read More

4BP160-10-2A-PP LC Bandpass Filter

December 13, 2013

4BP160-10-2A-PPPMI Model No. 4BP160-10-2A-PP is an LC Bandpass filter centered at 160 MHz with PC Pins in and out.

Read More

4BP160-20-2A-PP LC Bandpass Filter

December 13, 2013

4BP160-20-2A-PPPMI Model No. 4BP160-20-2A-PP is an LC Bandpass filter centered at 160 MHz with PC Pins in and out.

Read More

4BP160-40-2A-PP LC Bandpass Filter

December 13, 2013

4BP160-40-2A-PPPMI Model No. 4BP160-40-2A-PP is an LC Bandpass filter centered at 160 MHz with PC Pins in and out.

Read More

4BP160-5-2A-PP LC Bandpass Filter

December 13, 2013

4BP160-5-2A-PPPMI Model No. 4BP160-5-2A-PP is an LC Bandpass filter centered at 160 MHz with PC Pins in and out.

Read More

P1T-0R5G18G-60-T-512-SFF Absorptive Solid State Switch

December 13, 2013

P1T-0R5G18G-60-T-512-SFFPMI Model No. P1T-0R5G18G-60-T-512-SFF is a single pole, single throw, absorptive solid state switch that operates over the frequency range of 0.5 to 18.0 GHz.  This model has a maximum insertion loss of 3.5 dB and an isolation specification of 60 dB.  It operates at 20 dBm CW and can survive 1 W CW, 10 W peak for 1 uSec.

Read More

GMDA-D1003 Detector Log Video Amplifier

December 06, 2013

GMDA-D1003PMI Model No. GMDA-D1003 is a detector log video amplifier (DLVA) that operates between the 7.0 to 18.0 GHz frequency range.  It has a dynamic range of 75 dB, a log slope of 25 mV/dB and a nominal video bandwidth of 12 MHz. Furthermore, it has been designed using cutting edge GaAs technology which provides stunning performance and reliability in a compact package.

Read More

P2T-2G18G-55-T-512-SFF-LV Two Throw Switch

December 06, 2013

P2T-2G18G-55-T-512-SFF-LV (3)

PMI Model No. P2T-2G18G-55-T-512-SFF-LV is a terminated, single pole, two throw switch that operates from the 2.0 to 18.0 GHz frequency range and can handle +23 dBm CW input power with port to port isolation of 55 dB min.  This model has low insertion loss while still offering a fast switching speed of 50 nsec max.

Read More

PFS-618-CD-1 High Speed Frequency Synthesizer

December 04, 2013

PFS-618-CD-1PMI Model No. PFS-618-CD-1 is a high speed frequency synthesizer that operates over the frequency range of 6.0 to 18.0 GHz.  This model covers the complete 6.0 to 18.0 GHz frequency in 100 kHz steps with an output power of +10 dBm minimum.  The unit is accurate to within ±1 MHz and settles within 1 usec maximum.

Read More

024142SA Successive Detection Log Video Amplifier

November 27, 2013

024142SAPMI Model No. 024142SA is a successive detection log video amplifier (SDLVA) that operates over a frequency range of 18.0 to 40.0 GHz.  It has a dynamic range of 65 dB, log slope of 25 mV/dB and a nominal video bandwidth of 32 MHz.  It has been designed using cutting edge GaAs technology which provides stunning performance and reliability.

Read More

P16T-100M20G-60-T-512-SFF Pin Diode Switch

November 27, 2013

P16T-100M20G-60-T-512-SFFPMI Model No. P16T-100M20G-60-T-512-SFF is a single pole, sixteen throw, absorptive pin diode switch that operates at a frequency range of 0.1 to 20.0 GHz.  This model has a typical insertion loss of 8.5 dB and 60 dB of isolation.  It operates at 20 dBm CW and has a survival power of 1 W CW, 10 W peaks for 1 microsecond.

Read More

PE2-30-1R018R0-4R5-22-12-SFF-1 Low Noise Amplifier

November 27, 2013

PE2-30-1R018R0-4R5-22-12-SFF-1PMI Model No. PE2-30-1R018R0-4R5-22-12-SFF-1 is a 1.0 to 18.0 GHz, low noise amplifier that typically provides 30 dB of gain while maintaining a maximum gain flatness of ±1.5 dB over the operating frequency.  The noise figure is 4.5 dB max and offers an OP1 dB of 22 dBm min.  The operating voltage is +12 to +15 VDC with a typical current draw of 500 mA.

Read More

PIFA-9D4G-1D8G-1 Frequency Down Converter

November 27, 2013

PIFA-9D4G-1D8G-1PMI Model No. PIFA-9D4G-1D8G-1 is an integrated frequency down converter used within Doppler Radar Systems.  The RF Input is 9.4 GHz +/- 30 Mhz with an input dynamic range of 100 to 0 dBm.  The LO Input is 2.803 GHz +/- 15 Mhz with a power level of +5 to +7 dBm.  The resulting IF output frequency is 1.8 GHz +/- 10 MHz.

Read More

SWN-1170-4DT-SP Absorptive Switch

November 27, 2013

SWN-1170-4DT-SPPMI Model No SWN-1170-4DT-SP is a single pole, four throw, absorptive switch designed to operate over the 0.5 to 18.0 GHz frequency range.  This model is designed to maintain low insertion loss, high isolation and fast switching speed.  It is supplied with removable 2.92 mm (F) connectors in a radial housing that measures 1.25" dia x 0.7" thick.

Read More

SWN-2181-TRA Pin Diode Transfer Switch

November 27, 2013

SWN-2181-TRAPMI Model No. SWN-2181-TRA is a pin diode transfer switch that operates over a frequency range of 0.5 to 18.0 GHz.  It has 60 dB min of isolation,, max insertion loss of 3.5 dB and a max input power of +10 dBm CW.  This model incorporates a TTL compatible driver for easy system integration and is supplied with removable 2.92 mm (F) connectors in a housing that measures 1.0" x 1.0" x 0.25".

Read More

LM -2G18G-2D8-33DBM-12V Active Limiter

November 12, 2013

LM-2G18G-2D8-33DBM-12VPMI Model No. LM-2G18G-2D8-33DBM-12V is an active limiter that operates over a frequency range of 2.0 to 18.0GHz with max input power of +33 dBm CW and a maximum leakage power of +2.8 dBm. The VSWR is 2.0:1 max the operating voltage is +12 VDC with a current draw of 180 mA max.. The unit is supplied with removable SMA(F) connectors in our standard PE2 housing.

Read More

LM-500M8G-2-33DBM-12V Active Limiter

November 12, 2013

LM-500M8G-2-33DBM-12VPMI Model No. LM-500M8G-2-33DBM-12Vis an active limiter that operates over a frequency range of 0.5 to 8.0 GHz with a maximum input power of +33 dBm CW and a maximum leakage power of +2.3 dBm.  The VSWR is 2.0:1 and the operating voltage is +12 VDC with a typical current draw of 180 mA.  The unit is supplied with removable SMA(F) connectors in our standard PE2 housing.

Read More

LM-8G18G-7-33DBM-12V Active Limiter

November 12, 2013

LM-8G18G-7-33DBM-12VPMI Model No. LM-8G18G-7-33DBM-12V is an active limiter that operates over a frequency range of 8.0 to 18.0 GHz with a maximum input power of +33 dBm CW and a maximum leakage power of +7.1 dBm.  The VSWR is 2.0:1 and the operating voltage is +12 VDC with a maximum current draw of 100 mA. The unit is supplied with removable SMA(F) connectors in our standard PE2 housing.

Read More

P2T-8G12G-90-T-SFF Solid State Switch

November 12, 2013

P2T-8G12G-90-T-SFFPMI Model No. P2T-8G12G-90-T-SFF is a single pole, two throw terminated solid state switch. This model operates over the frequency range of 8.0 to 12.0 GHz and has a typical insertion loss of 2.4 dB, isolation of 75 dB minimum and a typical switching speed of 15 nsec. This unit is capable of operating with RF input power levels up to 20 dBm CW.

Read More

P2T-9D25G-80-R-SFF-3W Pin Diode Switch

November 12, 2013

P2T-9D25G-80-R-SFF-3WPMI Model No. P2T-9D25G-80-R-SFF-3W is a single pole, two throw, reflective pin diode switch that operates over a single frequency range of 9.25 +/- 30 MHz.  This model has a maximum insertion loss of 34 dBm CW and a minimum isolation specification of 80 dB. It operates at 34 dBm CW max, or +33 dBm, 2 microsecond pulse width (PW) and 8KHz (operating).

Read More

PIQ-2G18G-360-16-CD-1 I/Q Vector Modulator

November 12, 2013

PIQ-2G18G-360-16-CD-1PMI Model No. PIQ-2G18G-360-16-CD-1 is a 2.0 to 18.0 GHz, high performance I/Q vector modulator with 2 x 12 bit monotonic TTL compatible channels (I and Q).  This model offers a full 360 degrees of phase shift with a minimum of 16 dB of amplitude control.

Read More

TD-30T-SHS-218-2G4G-PECL Threshold Detector

November 12, 2013

TD-30T-SHS-218-2G4G-PECLPMI Model No. TD-30T-SHS-218-2G4G-PECL is a high speed, LVPECL logic output threshold detector designed to operate from 2.0 to 18.0 GHz, but optimized for 2.0 to 4.0 GHz.  This detector has a propagation delay of 15 ns max and has a LVPECL output.

Read More

A Medium Power Amplifier: PA-40-17D521D5-5R0-36-12-292FF

November 11, 2013

PA-40-17D521D5-5R0-36-12-292FFPMI Model No. PA-40-17D521D5-5R0-36-12-292FF is a medium power amplifier that operates over the frequency range of 15.7 to 21.5 GHz.  It has a nominal gain of 40 dB typical with a maximum gain flatness of +/-1.75 dB and a typical noise figure of 5.0 dB. It is supplied with SMA(F) connectors in a housing that measures 2.6" x 2.0" x 0.5"

Read More

Front End Amplifier: PEC-14-127-8-12-SFF Rev B

November 11, 2013

PEC-14-127-8-12-SFF Rev BPMI Model No. PEC-14-127-8-12-SFF Rev B is a wide band front end amplifier that operates over the frequency range of 1.0 to 26.5 GHz.  This model provides gain of 13 to 17 dBm and has a maximum gain flatness of +/-1.5 dB.  The maximum noise figure is 5.5 dB from 1.0 to 20.0 GHZ and 6.0 dB from 20.0 to 26.5 GHz. The housing measures 0.83" x 0.75" x 0.36" and is supplied with removable SMA connectors.

Read More

GMTA-1005 Threshold Detector

November 11, 2013

GMTA-1005PMI Model No. GMTA-1005 is a threshold detector designed to operate over the frequency range of 8 to 18 GHz.  It has a fixed threshold level of -42 dBm with threshold stability of +/-3.0 dBm over frequency and temperature.

Read More

HADA-D2002 Detector Log Video Amplifier

November 11, 2013

HADA-D2002PMI Model No. HADA-D2002 is a Detector Log Video Amplifier (DLVA) that operates between the frequency range of 2.0 to 18.0 GHz.  It has a dynamic range of 40 dB with a log slope of 50 mV/dB and a nominal video bandwidth of 12 MHz.  This unit has been designed with cutting edge technology which provides stunning performance and high reliability in a compact package.

Read More

Limiting Amplifier: PEC2-8G18G-21DBM-LM-SFF

November 11, 2013

PEC2-8G18G-21DBM-LM-SFFPMI Model No. PEC2-8G18G-21DBM-LM-SFF is an 8.0 to 18.0 GHz limiting amplifier that provides an nominal output power level of +20.0 dBm for an input power range of -50 to +10 dBm CW.  This model has output power level versus frequency range compensation such that the limited output power has a flat frequency response. The unit is supplied in a small housing measuring only 2.98" x 0.78" x 0.36".

Read More

LM-8G18G-7-33DBM-12V Active Limiter

November 11, 2013

LogoPMI Model No. LM-8G18G-7-33DBM-12V is an active limiter that operates over a frequency range of 8.0 to 18.0 GHz with a maximum input power of +33 dBm CW and a maximum leakage power of +7.1 dBm.  The VSWR is 2.0:1 and the operating voltage is +12 VDC with a maximum current draw of 100 mA.

Read More

Low Noise Amplifier: PE2157R52015SFF Rev. D

November 11, 2013

PE2157R52015SFF Rev  DPMI Model No. PE2157R52015SFF Rev. D is a 7.5 to 20.25 GHz, low noise amplifier that provides a small gain window of 14.5 to 17.5 with a typical gain flatness of +/-1.5 dB.  The noise figure is 6.0 dB max and offers an OP1 dB of 18.0 dBm min.  The operating voltage is +15 VDC and the current draw is 300 mA max.  This unit is supplied with removable SMA(F) connectors in our standard PE2 housing.

Read More

Pin Diode Attenuator: DTA-2G18G-60-CD-2-OPT-1G18G

November 11, 2013

DTA-2G18G-60-CD-2-OPT-1G18GPMI Model DTA-2G18G-60-CD-2-OPT-1G18G is a non-reflective, 10 BIT, programmable 60 dB, pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 1.0 to 18.0 GHz.  This model is offered in a slim line housing measuring only 0.5" H.

Read More

SDLVA-0R81R6-75-CD-3 Successive Detection Log Video Amplifier

November 11, 2013

LogoPMI Model No. SDLVA-0R81R6-75-CD-3 is a successive detection log video amplifier (SDLVA) that operates between the 850 to 1550 MHz frequency range.  It has a dynamic range of 75 dB, a log slope of 40 mV/dB and a nominal video bandwidth of 20 MHz.  It has been designed using cutting edge GaAs technology which provides stunning performance and reliability in a compact package.

Read More

Two Channel Switch Filter: 2SFB-8G26G-CD-SFF Rev C

November 11, 2013

2SFB-8G26G-CD-SFF Rev CPMI Model No. 2SFB-8G26G-CD-SFF Rev C is a 2 channel switch filter bank providing a low-pass filter that passes 8.62 to 8.70 GHz with a rejection band of 17.24 to 17.4 GHz.  In by-pass mode the unit passes signals from 8.0 to 26.5 GHz.  This unit is powered by a +5 V single supply and the control logic is TTL/CMOS +5 V compatible.

Read More

Vector Modulator: PIQ-85M18G-360/20-CD-2

October 17, 2013

PIQ-85M18G-36020-CD-2

PMI model number PIQ-85M18G-360/20-CD-2 is a vector modulator covering the frequency range of 85 MHz to 18 GHz. This unit provides an attenuator resolution of 0.08 dB and a phase shift resolution of 0.703125. The attenuation is phase invariant and the phase is amplitude invariant making it ideal for nulling unwanted signals. The unit can be specifically calibrated for any number of 100 MHz bands within the frequency range.

Read More

Low Noise Amplifier: PE2-15-8G20G-4R0-20-SFF

October 16, 2013

PE2-15-8G20G-4R0-20-SFFPMI Model No. PE2-15-8G20G-4R0-20-SFF is a 8.0 to 20.0 GHz, low noise amplifier that provides 12 dB min of gain with a typical gain flatness of +/-1.25 dB. The noise figure is 4.0 dB typ and offers an OP1 dB of 20 dBm typ.  The operating voltage is +11 to +15 VDC and the current draw is 225 mA nom.

Read More

Low Noise Amplifier: PE2-30-1R06R0-1R5-22-12-SFF

October 16, 2013

PE2-30-1R06R0-1R5-22-12-SFFPMI Model No. PE2-30-1R06R0-1R5-22-12-SFF is a 1.0 to 6.0 GHz, low noise amplifier that provides 30 dB of gain typically.  The typical noise figure is 1.8 dB and offers an OP1 dB of 22 dBm typ.  The operating voltage is +12 to +15 VDC max and the current draw is 320 mA typ.

Read More

Low Noise Amplifier: PLN-17-110-15-LCA

October 16, 2013

PLN-17-110-15-LCAPMI Model No. PLN-17-110-15-LCA is a 1.0 to 10.0 GHz, low noise amplifier that typically provides 17 dB of gain.  The typical noise figure is 2.0 dB and offers an OP1 dB of 13 dBm min.  The operating voltage is +12 to +15 VDC and the current draw is 65 mA max.

Read More

Low Noise Amplifier: PE210R258R515SFFLM Rev. B

October 16, 2013

PE210R258R515SFFLM Rev  BPMI Model No. PE210R258R515SFFLM Rev. B is a 0.25 to 8.5 GHz, low noise amplifier with a small signal gain window of +9.0 to +13 dB.  The noise figure for this unit is <=4.5 dB max (valid from 0.5 to 8.5 GHz) and offers an OP1 dB of +16 dB min.  The operating voltage is +12 VDC and the current draw is 300 mA max.

Read More

Single Throw Switch: P1T-9D25G-90-T-SFF

October 16, 2013

P1T-9D25G-90-T-SFFPMI Model No. P1T-9D25G-90-T-SFF is a high speed, solid state, single pole single throw switch capable of switching within 20 ns. The frequency range is 9.25 GHz (+/- 30 MHz) with > 90 Db of isolation.

Read More

Detector Log Video Amplifier: HADA-D2001

October 11, 2013

HADA-D2001PMI Model No. HADA-D2001 is a detector log video amplifier (DLVA) that operates between the 0.5 to 2.0 GHz frequency range.  It has a dynamic range of 40 dB, a log slope of 50 mV/dB and a nominal bandwidth of 20 MHz.  It has been designed using cutting edge technology which provides stunning performance and reliability in a compact package.

Read More

Ultra-Wideband LNA: PEC-42-1G40G-20-12-292FF

October 11, 2013

PEC-42-1G40G-20-12-292FFPMI Model No. PEC-42-1G40G-20-12-292FF is a 1.0 to 40 GHz, ultra-wideband low noise amplifier that provides 42 dB of gain typically with a typical noise figure of 5.5 dB.  The OP1dB is typically +22 dBm (1.0 to 18.0 GHz) and +19 dBm (18.0 to 40.0 GHz). The maximum input power rating is +17 dBm CW and the operating DC supply is 550 mA at +12 to +15 VDC. 

Read More

Amplifier w/Gain Window: PM2-34-218-15-SFF-1

September 30, 2013

PM2-34-218-15-SFF-1PMI Model No. PM2-34-218-15-SFF-1 is a 2.5 to 18.0 GHz low noise amplifier with a gain window of 32.0 to 36.0 dB at -40ºC to +95ºC and 32.0 to 37.0 dB at -54º Cto +95º C and a gain flatness of +/-1.5 dB max.

Read More

Amplifier: PEAFS3-12-218-15-SFF-1

September 30, 2013

PEAFS3-12-218-15-SFF-1PMI Model No. PEAFS3-12-218-15-SFF-1 is a 2.0 to 18.0 GHz low noise amplifier that provides +15 to +22 dB of gain.  The noise figure is 5.0 dB max from 2.0 to 4 GHz and 4.1 dB max at 4.0 to 18.0 GHz and offers an OP1 dB of +9 dBm min.  The operating voltage is +15 VDC and the current draw is 180 mA max.

Read More

Four Way Power Divider: APD-4-218

September 30, 2013

APD-4-218PMI Model No. APD-4-218 is a high reliable four way power divider featuring excellent amplitude and phase balance, low insertion loss, and high isolation electrically, and removable I/O SMA connectors mechanically.

Read More

Low Noise Amplifier: POB-15-818-13-LCA Rev.B

September 30, 2013

POB-15-818-13-LCA Rev BPMI Model No. POB-15-818-13-LCA Rev.B is a 8.0 to 18.0GHz, low noise amplifier which provides 15 dB of gain while maintaining a gain flatness of +/-1.5 dB typically over the operating frequency. The noise figure is 3.0 dB typical and offers a typical OP1dB of +13dBm.  The amplifier requires +12 VDC and has a typical current draw o f 75 mA. 

Read More

Temperature Compensated LNA: PE2-34-1R251R75-12-SFF-1

September 30, 2013

PE2-34-1R251R75-12-SFF-1PMI Model Number PE2-34-1R251R75-12-SFF-1 is a 1.25 to 1.75 GHz, temperature compensated, low noise amplifier with 34 dB of gain with a typical gain flatness of +/-0.25 dB. The noise figure is typically 4.98 dB and offers a minimum OP1 dB of 0 dBm.  The amplifier requires +7 to +12 VDC and the current draw is 198 mA typical.

Read More

Absorptive Switch: P2T-8G12G-100-T-55-SFF

September 17, 2013

P2T-8G12G-100-T-55-SFFPMI Model No. P2T-8G12G-100-T-55-SFF is a single pole, two throw, high power, absorptive switch.  This switch has high isolation of 100 dB min and low insertion loss of 3.0 dB typical (5.0 dB max).  It offers a high switching speed of 100 ns max and has an integral TTL driver.

Read More

Absorptive Switch: P5T-500M40G-60-T-55-292FF-5G40G

September 17, 2013

P5T-500M40G-60-T-55-292FF-5G40GPMI Model No. P5T-500M40G-60-T-55-292FF-5G40G is an SP5T, absorptive switch that operates from 0.5 to 40.0 GHz.  This switch has an insertion loss of < 8.0 dB max,  >60 dB of isolation and is supplied in a small housing measuring 1.353" dia x 0.40" thick.

Read More

Absorptive Switch: P1T-500M40G-55-T-292FF

September 17, 2013

P1T-500M40G-55-T-292FFPMI Model No. P1T-500M40G-55-T-292FF is an SPST, high speed, absorptive switch. This switch operates at a frequency range of .5 to 40.0 GHz and is capable of switching within 100 ns.  It has 55 dB of isolation and insertion loss of 5.5 dB max.

Read More

Bandpass Filter : BPF3D875-2D25-CD-SFF

September 17, 2013

BPF3D875-2D25-CD-SFFPMI Model No. BPF3D875-2D25-CD-SFF is a Bandpass filter that has a center frequency of 3.875GHz and a Passband of 2.25GHz.  The passband insertion loss is 2.0dB max with a VSWR of 2.0:1 max.  The filter measures 2.50" x 0.8" x 0.5" and is supplied with SMA Female connectors.

Read More

Low Noise Amplifier: PE2-60-2G8G-2R5-20-12-SFF

September 17, 2013

PE2-60-2G8G-2R5-20-12-SFFPMI Model Number PE2-60-2G8G-2R5-20-12-SFF is a 2.0 to 8.0 GHz low noise amplifier which produces 60 dB of gain with a maximum noise figure of 2.5 dB.  The OP1dB is >20 dBm and the VSWR is 2.0:1 maximum. This amplifier operates on a DC voltage supply of +12 to +15 volts and the current draw is 475 mA maximum.  The housing measures 2.98” x 0.78” x 0.26” and is supplied with SMA female connectors.

Read More

Programmable Attenuator: DTA-22G28G-50-CD-1

September 17, 2013

DTA-22G28G-50-CD-1PMI Model DTA-22G28G-50-CD-1 is a 50 dB monotonic programmable attenuator with 11-bit resolution that provides a step size of 0.025 dB. It has also been designed to have very low insertion loss over the frequency range of 22.5 to 27.5 GHz.

Read More

Reflective Switch: P2T-8G18G-45-R-SFF-HP20W

September 17, 2013

P2T-8G18G-45-R-SFF-HP20WPMI Model No. P2T-8G18G-45-R-SFF-HP20W is an SP2T, high power (20 W), reflective switch.  This switch operates on a frequency of 8.0 to 18.0 GHz.  It has a low insertion loss of 2.5 dB max and an integral TTL driver and is hermetically sealed.

Read More

Reflective Switch: P2T-960M977M-30-R-528-SFF-20W

September 17, 2013

P2T-960M977M-30-R-528-SFF-20WPMI Model No. P2T-960M977M-30-R-528-SFF-20W is a single pole, two throw, reflective switch capable of handling input power up to 20 W CW. The frequency range is 960 to 977 MHz and it has over 40 dB of typical isolation with a switching speed of less than 40 nsec. The unit is supplied with SMA Female connectors in a package measuring 1.2" x 1.0" x 0.5".

Read More

Reflective Switch: P2T-5G5D15G-30-R-528-SFF-20W

September 17, 2013

P2T-5G5D15G-30-R-528-SFF-20WPMI Model No. P2T-5G5D15G-30-R-528-SFF-20W is a single pole, two throw, reflective switch capable of handling input power up to 20 W CW. The frequency range is 5000 to 5150 MHz and it has 30 dB of isolation with a switching speed of less than 40 nsec. The unit is supplied with SMA Female connectors in a package measuring 1.2" x 1.0" x 0.5".

Read More

Video Amplifier: SDLVA-100M4G-CD-2

September 17, 2013

SDLVA-100M4G-CD-2PMI Model No. SDLVA-100M4G-CD-2 is a successive detection log video amplifier (SDLVA) that operates between the 100 to 4000 MHz frequency range and is capable of extending to 6000 MHz.  It has a dynamic range of 70 dB, a log slope of 25 mV/dB and a nominal video bandwidth of 11.67 MHz.

Read More

Absorptive Switch: P8T-500M40G-60-T-55-292FF

August 05, 2013

p8t-500m40g-60

PMI Model No. P8T-500M40G-60-T-55-292FF is a high speed, single pole, eight throw, absorptive switch operating over the frequency range of 0.5 to 40 GHz.  This switch has over 60 dB of isolation and is capable of switching within 50 ns.

Read More

Absorptive Switch: P4T-50M40G-55-T-292FF

July 29, 2013

P4T-50M40G-55-T-292FFPMI Model No. P4T-50M40G-55-T-292FF is a 50 MHz to 40.0 GHz, single pole, four throw, absorptive switch.  This switch offers 55 dB of port to port isolation and a maximum insertion loss of 8 db. It has a switching speed of 100 ns and is independently TTL controlled.  The operating power is +20 dBm CW and it has a VSWR of 2.5:1 max.   

Read More

Active Limiter: LM-10G-3-26DBM-12V

July 15, 2013

LM-10G-3-26DBM-12VPMI Model No. LM-10G-3-26DBM-12V is an active limiter that operates at 10 GHz and provides an input dynamic range of -45 to +26 dBm.  This limiter offers very hard limiting at 0 dBm typically and 3 dBm maximum.  The VSWR on average is better than 1.4:1 and operating voltage is +12 to +15 VDC with a current draw of 10 0mA.

Read More

Low Noise Amplifier: PEC-42-500M40G-20-12-292MM

July 10, 2013

PEC-42-500M40G-20-12-292MMPMI Model No. PEC-42-500M40G-20-12-292MM is a 500 MHz to 40 GHz ultra-wideband low noise amplifier that provides typically 42 dB of gain with a noise figure of 5.5 dB at 2 0GHz.  The OP1 dB is typically +22 dBm (1.0 to 18.0 GHz) and +1 9dBm (18.0 to 40.0 GHz). 

Read More

Programmable Pin Diode Attenuator: DTA-0R5G18G-60-CD-1

July 08, 2013

DTA-0R5G18G-60-CD-1PMI Model No. DTA-0R5G18G-60-CD-1 is a non-reflective, 10 bit, programmable 60 dB pin diode attenuator with step resolution as low as 0.06 dB over the frequency range of 0.5 to 18.0 GHz.

Read More

SDLV Amplifier: SDLVA-2G6G-70-CD-1

July 08, 2013

SDLVA-2G6G-70-CD-1PMI Model No. SDLVA-2G6G-70-CD-1 is a successive detection log video amplifier (SDLVA) that operates between the 2.0 to 6.0 GHz frequency range. It has a dynamic range of 70 dB, a log slope of 40 mV/dB and offers very fast rise and fall times of 15 and 25 nsec respectively.

Read More

Two Throw Switch: P2T-12G18G-45-R-SFF-10W

July 08, 2013

P2T-12G18G-45-R-SFF-10WPMI Model No. P2T-12G18G-45-R-SFF-10W is an independently controlled, high power, reflective single pole two throw switch designed to operate between 12.0 to 18.0 GHz and handle input power levels up to 10 W CW and 30 W peak with a maximum pulse width of 1usec and maximum PRF of 2 MHz.

Read More

High Power Limiter: LM-0518-10-1W-SHS-M-1218

June 20, 2013

LM-0518-10-1W-SHS-M-1218PMI Model No. LM-0518-10-1W-SHS-2-M-1218 is a high power limiter that operates from 12.0 to 18.0GHz.  This limiter handles 100 W peak power with a pulse width of 1usec.  The insertion loss is only 1.5dB typically and has a VSWR of 2.0:1 maximum.

Read More

Multi-Function Module: PFEM-9D4G-CD-1

June 20, 2013

PFEM-9D4G-CD-1PFEM-9D4G-CD-1 is a multi-function module that provides amplification, switching and filtering within the frequency band of 9410 MHz.  This module provides two input channels and is switchable to a common output.  This model is designed to offer multiple gain level selection, high channel to channel isolation and fast switching speeds.

Read More

Pin Diode Switch: P2T-1G18G-10-R-5V-SFF-HIP10W-HERM

June 17, 2013

P2T-1G18G-10-R-5V-SFF-HIP10W-HERMPMI Model No. P2T-1G18G-10-R-5V-SFF-HIP10W-HERM is a hermetically sealed, reflective, single pole, two throw pin diode switch that operates over the 1.0 to 18.0GHz frequency range.  This model is capable of handling an input power level of 5 WCW while providing switching speeds of less than 40ns typically.

Read More

Log Video Amplifier: SDLVA-3G18G-CW-70-MAH

June 10, 2013

SDLVA-3G18G-CW-70-MAHPMI Model No: SDLVA-3G18G-CW-70-MAH is a CW-immune successive detection log video amplifier operating in the 2.0 to 18.0 GHz frequency band.  It features an SPST on the RF output which allows for the RF to be blanked when the RF input signal is below the -64 dBm threshold.

Read More

Hard Diode Limiter: LM-0518-10-1W-SHS-1-F

May 24, 2013

LM-0518-10-1W-SHS-1-FPMI Model No. LM-0518-10-1W-SHS-1-F is a high speed, high power, hard diode limiter that operates over the frequency range of 0.5 to 18.0 GHz.  This limiter handles 100 W peak power with a pulse width of 1 us.  The insertion loss is less than 2 dB typically and has a VSWR of 2.0:1 maximum.

Read More

Diplexer: 11DP-11R5/16R5-CD-SFF-1

May 23, 2013

11DP-11R5-16R5-CD-SFF-1PMI Model No. 11DP-11R5/16R5-CD-SFF-1 is a diplexer that offers pass bands at 10.75 to 12.25 GHz and 15.75 to 17.25 GHz.  The pass band insertion loss is less than 3 dB and the VSWR is 1.5:1 maximum.  Filter channel 1 has a pass band of 10.75 to 12.25 GHz and offers -50 dBc of rejection at 10.25 GHz and -75 dBc of rejection at 13.75 GHz.  Filter channel 2 has a pass band of 15.75 to 17.25 GHz and offers -50 dBc of rejection at 17.75 GHz and -75dBc of rejection at 14.25 GHz. 

Read More

Digitally Controlled Phase Shifter: PS-360-3237-8-292FF

May 06, 2013

PS-360-3237-8-292FF

PMI Model No. PS-360-3237-8-292FF is a high speed, millimeter wave, 8-bit digitally controlled, phase shifter that operates over the frequency range of 32.0 to 37.0 GHz.  This phase shifter offers a low insertion loss of 13 dB typically and maintains a VSWR of 1.8:1.  The total phase shift range is 358.593° having a step size of 1.406° and switches between states in less than 500 ns.

Read More

Digitally Programmable Attenuator: PDVAN-8018-60-8-OPT25DBM

May 06, 2013

PDVAN-8018-60-OPT25DBMPMI Model No. PDVAN-8018-60-8-OPT25DBM is an 8-Bit digitally programmable attenuator that operates over the frequency range of 8.0 to 18.0 GHz.  This model offers low loss of 3.6 dB typically and an attenuation range of 60 dB. This model was designed to handle input power levels up to +25 dBm CW under operating conditions and signal levels up to +30 dBm CW without damage. 

Read More

Eight Throw Absorptive Switch: P8T-2G6G-90-T-55-SFF

May 06, 2013

P8T-2G6G-90-T-55-SFF

PMI Model No. P8T-2G6G-90-T-55-SFF is a high speed, single pole, eight throw, absorptive switch that operates over the frequency range of 2.0 to 6.0 GHz.  This switch offers very-high isolation of 97 dB typical while maintaining a typical fast switching speed of 30 ns.  The operating input power rating is +23 dBm CW with an insertion loss of 3.5 dB.

Read More

High Power RF Limiter: LM-18G40G-18-1W-292FF

May 06, 2013

LM-18G40G-18-1W-292FF (2)PMI Model No. LM-18G40G-18-1W-292FF is an ultra-high speed, millimeter wave, high power RF limiter that operates over the frequency range of 18.0 to 40.0 GHz.  This limiter can handle input power levels up to 1 W CW and provides a leakage output power of +18 dBm maximum and +12 dBm typical.

Read More

High Power, Switch Box Assembly: PSD-2G6G-CD-1

May 06, 2013

PSD-2G6G-CD-1PMI Model No. PSD-2G6G-CD-1 is high power, switch box assembly that provides protection to front-end receivers when in the presence of high power signals.  This is accomplished by sensing the input signal level and then switching the input signal into 50 ohms terminations when a set threshold level is exceeded.  This assembly operates from 2.0 to 6.0 GHz and can handle input power levels up to 10 W CW.

Read More

HP Switch Box Assembly PSD-6G16G-CD-1

May 06, 2013

PSD-6G16G-CD-1PMI Model No. PSD-6G16G-CD-1 is high power, switch box assembly that provides protection to front-end receivers when in the presence of high power signals.  This is accomplished by sensing the input signal level and then switching the input signal into 50 ohms terminations when a set threshold level is exceeded.  This assembly operates from 6.0 to 18.0 GHz and can handle input power levels up to 10 W CW.

Read More

Limiting Amplifier: PEC3-40-1D6G2D7G-15LM-SFF

May 06, 2013

PEC3-40-1D6G2D7G-15LM-SFFPMI Model No. PEC3-40-1D6G2D7G-15LM-SFF is a limiting amplifier that operates over the frequency range of 1.6 to 2.7 GHz and offers a limited output of 15 dBm  ± 2 dBm.  The saturated power frequency flatness is ±1.5 dB maximum with a gain of 35 dB minimum and a typical noise figure of 4.5 dB.  The 2nd harmonic rejection is 24 dBc typically with an OIP3 of +18 dBm typical.

Read More

Low Noise Amplifier: POB-16-48-22-LCA

May 06, 2013

POB-16-48-22-LCAPMI Model No. POB-16-48-22-LCA is a 4.0 to 8.0 GHz low noise amplifier which provides 16 dB of gain while maintaining a gain flatness of ±1.0 dB typically over the operating frequency. The noise figure is 3 dB typical and offers a typical OP1 dB of +22 dBm. The amplifier requires +12 to +15 VDC and the current draw is 225 mA typical.

Read More

Low Noise Amplifier: PE2-25-218-20-12-SFF

March 19, 2013

PE2-25-218-20-12-SFFPMI Model No. PE2-25-218-20-12-SFF is a 2.0 to 18.0 GHz low noise amplifier that provides greater than 25 dB of gain while maintaining a maximum gain flatness of ±1.5 dB maximum over the operating frequency.  The noise figure is 4.5 dB typical and offers an OP1dB of +20 dBm minimum.  The operating voltage is +12 to 15 VDC and the current draw is 300 mA maximum.

Read More

Absorptive Switch: P4T-100M40G-90-T-512-292FF-SP

March 19, 2013

P4T-100M40G-90-T-512-292FFPMI Model No. P4T-100M40G-90-T-512-292FF-SP is a 100 MHz to 40 GHz, ultra-compact, high speed, single pole, four throw, absorptive switch.  This switch offers over 100 dB of port to port isolation from 100 MHz to 18 GHz, over 90 dB from 18 to 26.5 GHz and over 75 dB from 26.5 to 40 GHz.

Read More

Band Pass Filter: 7CL5125-1490-CD-SFF

March 19, 2013

7CL5125-1490-CD-SFFModel 7CL5125-1490-CD-SFF is a band pass filter centered at 5125MHz and has a nominal bandwidth of 1490MHz.  This filter provides over 40dB of rejection between 3.0 to 3.658GHz and between 6.65 to 7.3GHz and over 65dBc of rejection between 1.5 to 2.5GHz.

Read More

Bi-Phase Modulator: PS-180-4R15R3-SFF

March 19, 2013

PS-180-4R15R3-SFFPMI Model PS-180-4R15R3-SFF is a 0 /180 degrees, bi-phase modulator designed to operate over the 4.1 to 5.3 GHz frequency range.  This model can handle RF input signal levels up to +30 dBm without damage; has an insertion loss of 3.0 dB maximum and a maximum VSWR of 1.7:1.  A TTL control will switch between 0 degrees and 180 degrees phase states in less than 100 nsec.  The required supply voltages are ±5 VDC.

Read More

Low Noise Amplifier: PE2-35-1R02R0-1R4-17-12-SFF

March 19, 2013

PE2-35-1R02R0-1R4-17-12-SFFPMI Model No. PE2-35-1R02R0-1R4-17-12-SFF is a low noise amplifier that operates over the 1.0 to 2.0 GHz frequency range.  This model provides 35 dB of gain and offers a low noise figure of 1.4 dB typically.  The amplifier provides an OP1 dB is +17 dBm and operates on +12 to +15VDC with 160 mA of typical current draw.

Read More

Low Noise Amplifier: PEC-37-9G10G-3R0-27-SFF

March 19, 2013

PEC-37-9G10G-3R0-27-SFFPMI Model No. PEC-37-9G10G-3R0-27-SFF is a low noise amplifier that operates over the 9.0 to 10.0 GHz frequency range.  This model provides 28 dB of gain and offers a low noise figure of 3.0 dB maximum.  The amplifier provides an OP1 dB is +27 dBm minimum and operates on +10 to +15 VDC with 400 mA of typical current draw.

Read More

Low Noise Amplifier: PEC3-40-30M26R5G-6R0-12-12-SFF

March 19, 2013

PEC3-40-30M26R5G-6R0-12-12-SFFPMI Model No. PEC3-40-30M26R5G-6R0-12-12-SFF is a 30 MHz to 26.5 GHz low noise amplifier that provides greater than 35 dB of gain while maintaining a maximum gain flatness of ±3.5dB maximum over the operating frequency.  The noise figure is 6.0 dB typical and offers an OP1dB of +12 dBm minimum.  The operating voltage is +12 to 15 VDC and the current draw is 700 mA maximum.

Read More

Low Noise Amplifier: PUB-15-500M20G-20-LCA

March 19, 2013

PUB-15-500M20G-20-LCAPMI Model No. PUB-15-500M20G-20-LCA is a 500 MHz to 20.0 GHz low noise amplifier which provides 15 db of gain while maintaining a gain flatness of ±1.75 db typically over the operating frequency.  The noise figure is 3 dB typical and offers a typical OP1 dB of +20 dBm.  The amplifier requires +12 to +15 VDC and the current draw is 225 mA typical.

Read More

Successive Detection Log Video Amplifiers

March 19, 2013

SDLVA-315M362M-65-CD-1PMI model SDLVA-315M362M successive detection log video amplifiers (SDLVA) offers 65 dB dynamic range over the frequency range of 315 to 362 MHz.  This model offers a fast rise time of 35 nsec maximum and a recovery time of less than 500 nsec.  The unit is temperature compensated such that log accuracy over temperature remains less than +/-2.5 dB over the full operating temperature range of -33° to +77° C.

Read More

Log Video Amplifier: SDLVA-250M6G-CD-1

March 07, 2013

250m6g-cd-1PMI model SDLVA-250M6G-CD-1 successive detection log video amplifiers (SDLVA) offers 70 dB dynamic range over the frequency range of 0.25 to 6.0 GHz.  This model offers an ultra-fast rise time of 10nsec maximum and a recovery time of less than 60 nsec. The unit is temperature compensated such that log linearity over temperature remains less than +/-2.5 dB over the full operating temperature range of -40 to +70 C.

Read More

Log Video Amplifier: SDLVA-500M4G-CD-1

March 07, 2013

500m4g-cd-1PMI Model SDLVA-500M4G-CD-1 successive detection log video amplifiers (SDLVA) offers 70 dB dynamic range over the frequency range of 0.5 to 4.0 GHz.  This model offers an ultra-fast rise time of 10 nsec maximum, a recovery time of less than 60 nsec and a limited RF Output of +7 dBm. 

Read More

Broadband, Low Noise Amplifier: PEC-38-30M18G-12-SFF

February 12, 2013

PEC-38-30M18G-12-SFFPMI amplifier Model PEC-38-30M18G-12-SFF is a broadband, low noise amplifier that operates over the 30 MHz to 18 GHz frequency range.  This model provides 38 dB of gain and has a gain flatness of ±2.0 dB maximum.

Read More

Digitally Controlled Phase Shifter: PS-500M2G-8B-SFF

February 12, 2013

PS-500M2G-8B-SFFPMI Model No. PS-500M2G-8B-SFF is a State-Of-The-Art, 8-bit digitally controlled phase shifter that operates over the 500 MHz to 2.0 GHz frequency range.  This model has a typical insertion loss of 10 dB and offers 360 degrees of phase shift via 8-bit TTL control.

Read More

High Power Limiter: LM-26G40G-14-20W-292MM

February 12, 2013

LM-26G40G-14-20W-292MMModel LM-26G40G-14-20W-292MM is a high power limiter capable of withstanding an input power level of 20 W, 440 to 670 nsec pulse width, PRF 600 to 900 kHz, 40% duty cycle.  This model operates in the 26.5 to 40 GHz frequency range.  The insertion loss is 4.0 dB maximum, VSWR of 2.0:1 and 250 nsec response time and a typical leakage of +14 dBm.

Read More

Limiting Amplifier: PEC-85-0R32R5-15LM-12-SFF

February 12, 2013

PEC-85-0R32R5-15LM-12-SFFPMI Model No. PEC-85-0R32R5-15LM-12-SFF is a limiting amplifier that operates over the frequency range of 300 MHz to 2.5 GHz. This model provides a gain of 85 dB typically and a limited output of +15 dBm ± 2.5 dBm.

Read More

Low Noise Amplifier: PE2-1020-R518-15-SFF

February 12, 2013

PE2-1020-R518-15-SFF Rev  BPMI Model No. PE2-1020-R518-12-SFF is a low noise amplifier that offers a positive gain slope versus frequency. This type of amplifier is useful when trying to equalize frequency flatness over a broad bandwidth. This model provides 10 dB of gain at 500 MHz and 20 dB of gain at 18 GHz.

Read More

Low Noise Amplifier: PBB-20-218-16-LCA

February 12, 2013

PBB-20-218-16-LCAPMI Model No. PBB-20-218-16-LCA is a 2.0 to 18.0 GHz low noise amplifier which provides 20 dB of gain while maintaining a gain flatness of ±2.0 dB maximum over the operating frequency. The noise figure is 4 dB typical and offers a typical OP 1 dB of +14 dBm minimum.

Read More

Low Noise Amplifier: PEC3-33-218-20-15-SFF-HS-E

February 12, 2013

PEC3-33-218-20-15-SFF-HS-EPMI Model No. PEC3-33-218-20-15-SFF-HS-E is a 2.0 to 18.0 GHz low noise amplifier that provides greater than 33 dB of gain while maintaining a maximum gain flatness of ±2.0 dB maximum over the operating frequency.  The noise figure is 4 dB typical and offers an OP1 dB of +20 dBm minimum and an OIP3 of +30 dBm typical.  The operating voltage is +15 VDC and the current draw is typically 350 mA.

Read More

Solid-State Switch: P4T-100M2G-50-T-SFF-IN

February 12, 2013

P4T-100M2G-50-T-SFF-INPMI Model No. P4T-100M2G-50-T-SFF-IN is an absorptive, single pole, four throw solid-state switch that operates over the 100 MHz to 2.0 GHz frequency range.  The insertion loss is less than 3 dB and offers port to port isolation of over 50 dB.  The switching speed is 25 nsec maximum and the rise and fall times are less than 10 nsec.

Read More

Threshold Detector: CDT-2M18-30-BB-DE-D

February 12, 2013

CDT-2M18-30-BB Opt DE  DPMI Model CDT-2M18-30-BB Options DE, D is a threshold detector that operates over the 2 MHz to 18 GHz frequency range.  This model has a low insertion loss of 2.5 dB maximum and operates over an input power range of -30 to 0 dBm.  The threshold level is adjustable and the output signal is TTL positive logic.

Read More

Solid-State Switch: P4T-10G40G-60-T-GPO

February 06, 2013

p4t10g40g60tgpoPMI Model No. P4T-10G40G-60-T-GPO is a single pole, four throw, absorptive, solid-state switch that operated over the frequency range of 10 to 40 GHz.  This model provides over 60 dB of isolation and has an insertion loss of 6 dB maximum.  The VSWR is better than 2.0:1 into 50 ohm impedance.

Read More

360 Degree Phase Shifter: PS-360-DC-IR-9G10G

January 25, 2013

PS-360-DC-IR-9G10GThe PS-360-DC-IR-9G10G is a 10-Bit digitally controlled 360 degree phase shifter that operates from 9.0 to 10.0 GHz. This model offers low insertion loss of 7.5 dB and a phase shift accuracy of ±0.6 degrees typically.

Read More

Dielectric Resonator Oscillator: PIA-12D8G-CD-1

January 25, 2013

PIA-12D8G-CD-1PMI Model No. PIA-12D8G-CD-1 is a phase locked, dielectric resonator oscillator with internal reference having an output frequency of 12.8 GHz. This model provides a minimum output of +13 dBm with all spurs held to -80 dBc and harmonics held to -25 dBc.

Read More

High Power Limiter: LM-30M3G-C3-1

January 25, 2013

LM30m3gc31PMI Model Number LM-30M3G-C3-1 is a high power limiter that operates from 30 MHz to 3.0 GHz. This limiter can handle input power levels up to 5 W CW and provides a maximum leakage of +10 dBm. The insertion loss is 1.2 dB maximum with a maximum VSWR of 1.5:1. The recovery time is less than 1 usec.

Read More

Low Noise Amplifier: PUB-14-30M20G-14-LCA

January 25, 2013

PUB-14-30M20G-14-LCAPMI Model No. PUB-14-30M20G-14-LCA is a 30 MHz to 20.0 GHz low noise amplifier which provides 14 dB of gain while maintaining a gain flatness of ±1.2 dB typically over the operating frequency. The noise figure is 3 dB typical and offers an OP1 dB of +14 dBm typical.

Read More

Low Noise Amplifier: PE2-30-218-4R0-20-12-SFF-BT

January 25, 2013

PE2-30-218-4R0-20-12-SFF-BTPMI Model No. PE2-30-218-4R0-20-12-SFF-BT is a 2.0 to 18.0GHz low noise amplifier that has an integrated bias-tee network on the output port. This amplifier provides 30 dB of gain while maintaining a maximum gain flatness of ±2.0 dB max over the operating frequency.

Read More

Low Noise Amplifier: PUB-15-30M20G-20-LCA

January 25, 2013

PUB-15-30M20G-20-LCAPMI Model No. PUB-15-30M20G-20-LCA is a 30MHz to 20.0GHz low noise amplifier which provides 15 dB of gain while maintaining a gain flatness of ±2.5 dB typically over the operating frequency. The noise figure is 3 dB typical and offers a typical OP1 dB of +20 dBm. The amplifier requires +12 to +15 VDC and the current draw is 225 mA typical.

Read More

Detection Log Video Amplifier: SDLVA-0R71R3-75-CD-3

January 14, 2013

SDLVA-0R71R3-75-CD-3Model SDLVA-0R71R3-75-CD-3 is a successive detection log video amplifier that operates over the 700 to 1300 MHz frequency range. This model has a Dynamic Range of 75 dB, a log slope of 40 mV/dB.  The log linearity is ±1.2 dB typical from -65 to +5 dBm input power levels and a typical TSS of -70 dBm.

Read More

Log Video Amplifier: SDLVA-0R71R3-75-CD-1

January 08, 2013

SDLVA-0R71R3-75-CD-1Model SDLVA-0R71R3-75-CD-1 is a successive detection log video amplifier that operates over the 700 to 1300 MHz frequency range. This model has a dynamic range of 75 dB, a log slope of 40 mV/dB and a nominal video bandwidth of 20 MHz. This model offers very fast rise times of 9 nsec and fall times of 25 nsec typically.

Read More

Amplifier: PE2-30-0R56R0-5R0-22-12-SFF

January 07, 2013

PE2-30-0R56R0-5R0-22-12-SFFPMI Model No. PE2-30-0R56R0-5R0-22-12-SFF is a 500 MHz to 6.0 GHz low noise amplifier that typically provides 30 dB of gain. The gain flatness is ±1.0 dB maximum with a noise figure is 5.0 dB typical. This amplifier provides a minimum OP1 dB of +21 dBm.

Read More

Low Noise Amplifier: PS-360-900M930M-6-SFF

January 07, 2013

PE2-28-20R040R0-5R5-18-12-SFFPMI Model No. PE2-28-20R040R0-5R5-18-12-SFF is a 20 to 40GHz low noise amplifier that typically provides 28 dB of gain. The gain flatness is ±2.5 dB maximum and ±1.5 dB typical with a noise figure is 5.5 dB typical. This amplifier provides a minimum OP1 dB of +15 dBm minimum.

Read More

Low-Noise Amplifier: PEC2-60-4G8G-1R75-14-12-SFF

January 07, 2013

PEC2-60-4G8G-1R75-14-12-SFFPMI Model No. PEC2-60-4G8G-1R75-14-12-SFF is a 4 to 8 GHz low noise amplifier that typically provides 60 dB of gain. The gain flatness is ±1.25 dB maximum with a noise figure is 1.75 dB maximum. This amplifier provides a minimum OP1 dB of +14 dBm.

Read More

Phase Shifter: PS-360-900M930M-6-SFF

January 07, 2013

PS-360-900M930M-6-SFFPMI Model No. PS-360-900M930M-6-SFF is a 900 to 930 MHz, 6-BIT digitally controlled phase shifter having a LSB of 5.6 degrees. The insertion loss is 7 dB typical, 7.5 dB maximum with a typical VSWR of 2.0:1. This is a high speed phase shifter that can switch from one phase state to the next in typically 250 nsec.

Read More

RF Limiter: LM-6D7G7D9G-30W-SFF

January 07, 2013

LM-6D7G7D9G-30W-SFFPMI Model LM-6D7G7D9G-30W-SFF is a RF limiter that operates in the 6.7 to 7.9 GHz frequency range. This limiter can handle 30 W CW input power and provides a maximum leakage of +18 dBm. This model has a low insertion loss of 1.1 dB maximum and a recovery time of 10 usec maximum.

Read More

Solid-State Switch: P1T-26D532D5-90-1212-292FF

January 07, 2013

P1T-26D532D5-90-1212-292FFPMI Model No. P1T-26D532D5-90-1212-292FF is an absorptive, single pole, single throw, solid-state switch that operates over the frequency range of 26.5 to 32.5 GHz. This model provides a minimum isolation of 90 dB and maintains low insertion loss of 5.0 dB maximum. The VSWR is 2.0:1 maximum into 50 ohms impedance and offers switching speeds of 25 nsec maximum and 15 nsec typical.

Read More

Solid-State Switch: P4T-10G40G-60-T-GPO

January 07, 2013

P4T-10G40G-60-T-GPOPMI Model No. P4T-10G40G-60-T-GPO is a single pole, four throw, absorptive, solid-state switch that operated over the frequency range of 10 to 40 GHz. This model provides over 60 dB of isolation and has an insertion loss of 6 dB maximum. The VSWR is better than 2.0:1 into 50 ohm impedance.

Read More

Integrated, Dielectric Resonator Module: PIA-10G-CD-1

November 14, 2012

PIA10GCD1PMI Model No. PIA-10G-CD-1 is a 10 GHz integrated, dielectric resonator (DRO) module with three outputs, each having a 0 to 360 degree analog controlled, variable phase shifter and 0 to 10 dB analog controlled, variable output control capability on each of the outputs.  This model provides a low harmonic output of -50 dBc typical and an output power level of +19 dBm typical.  

Read More

Frequency Discriminator: FD-0518-10-812

October 31, 2012

FD-0518-10-812PMI Model No. FD-0518-10-812 is a 8.0 to 12.0 GHz frequency discriminator that provides a video output of 50 mV/GHz and has an accuracy of +/-200 MHz. The rise time is less than 20 nsec and operates into a 100 ohm video load. This model operates on +/-15 VDC and measures 2.0" x 1.8" x 0.5".

Read More

Band Reject Filter: BRF1370-50-CD-TNCFF

October 26, 2012

BRF1370-50-CD-TNCFF

PMI Model BRF1370-50-CD-TNCFF is a band reject filter with center frequency of 1370 MHz and a notch bandwidth of 60 MHz with a notch depth is 50 dB. This filter is rated to handle 10 W and is supplied with TNC connectors. The package measures 2.6" x 1.0" x 0.75".

Read More

Bandpass Filter: BPF1370-50-CD-TNCMF

October 26, 2012

BPF1370-50-CD-TNCMF

PMI Model BPF1370-50-CD-TNCMF is a band pass filter with a center frequency of 1370 MHz and a 1dB bandwidth of 50 MHz. This filter provides an ultimate stop-band rejection of 60 dBc and is rated to handle an input signal level of 6 W, 10% duty factor. This model offers low loss of less than 3 dB and is supplied in a package measuring 2.6" x 1.0" x 0.75".

Read More

SP2T Switch: P2T-14D415D4-15-SMT-20W

September 04, 2012

P2T-SMT-20WPMI Model No. P2T-14D415D4-15-SMT-20W is a driverless high-power SP2T switch in a compact package designed for surface mount applications. This switch operates from 14.4 to 15.4 GHz and has an insertion loss of 1.2 dB maximum at +25° C.

Read More

Controlled Attenuator / Analog Phase Shifter: PSAT-2500-11B-CD-1

July 24, 2012

PSAT-2500-11B-CD-1PMI Model PSAT-2500-11B-CD-1 is a 2.5GHz, 11 Bit Digitally Controlled Attenuator / Analog Phase Shifter assembly having the capability for phase shifting from 0 to 360° with an attenuation range of 60 dB minimum. This model has insertion loss of 10 dB maximum and a VSWR of 1.5:1 maximum into 50 ohms.

Read More

Digitally Controlled Oscillator: DTO-2G18G-CD-1

July 03, 2012

DTO-218-CD-1PMI Model No. DTO-2G18G-CD-1 is a digitally controlled oscillator (DTO) covering the frequency range of 2 to 18 GHz. This model is designed to withstand stringent military ground or airborne environments.

Read More

Detector Log Video Amplifier: PLVA-500M18G-50

June 29, 2012

PLVA-500M18G-50PMI Model PLVA-500M18G-50 is a 50 dB detector log video amplifier designed to operate over the 500 MHz to 18.0 GHz frequency range. This model employs planar diode detectors and integrated video circuitry for high speed performance and outstanding reliability.

Read More

Reflective Switch: P4T-4G12G-35-R-SFF-PM

June 29, 2012

P4T-4G12G-35-R-SFF-PMPMI Model No. P4T-4G12G-35-R-SFF-PM is a single pole, four throw, reflective switch that operates over the 4.0 to 12.0 GHz frequency range. This model features low insertion loss of 1.0 dB typical and isolation of 70 dB typical. All ports are phase matched to be within ±7.5 degrees.

Read More

High-Power SP2T Switch: P2T-14D415D4-15-SMT-20W

June 19, 2012

P2T-14D415D4-15-SMT-20WPMI Model No.P2T-14D415D4-15-SMT-20W is a driverless high-power SP2T switch in a compact package designed for surface mount applications. This switch operates from 14.4 to 15.4 GHz and has an insertion loss of 0.5 dB maximum. The Tx/Rx isolation is 15 dB minimum and this switch can handle input power levels up to 20 watts. The size of this SMT switch is 0.35" x 0.5" x 0.21".

Read More

Band Reject Notch Filter

May 14, 2012

BRF17D6G-20M-CD-1PMI Model BRF17D6G-20M-CD-1 is a band reject "notch" filter having a pass band of DC to 17.47GHz and 17.77 to 20 GHz and over 40 dB of rejection at 17.59 to 17.61 GHz. Insertion loss in the pass band is less than 5 dB and VSWR is better than 2.0:1. This filter is supplied with SMA female connectors and the size is 1.5" x 0.5" x 0.68".

Read More

Phase Shifter: PS-360-8D5G11G-8-SFF-LVT

May 09, 2012

PS-360-8D5G11G-8-SFF-LVTPMI Model Number PS-360-8D5G11G-8-SFF-LVT is an 8.5 to 11 GHz, 8 Bit digitally controlled phase shifter with capability of phase shift ranges from 0 to 360 degrees. The phase shift resolution is 1.41 degrees and controlled by eight, low voltage TTL control lines. This model has a typical insertion loss of 8 dB and phase accuracy of ±8.5 degrees.

Read More

USB Style RF & Microwave Control Components/LNA's

May 07, 2012

USBstylerRF-MicrowPlanar Monolithics Industries, Inc. introduces new USB style RF & microwave control components and LNA's to 40 GHz. RF & microwave USB style components & LNA’s featuring: 50 MHz to 40 GHz low noise amplifier, 500 MHz to 40 GHz SPDT absorptive switch, and 100 MHz to 40 GHz variable attenuator.

Read More

High Speed Threshold Detector: TD-16G40G-20-292F

May 03, 2012

TD-16G40G-20-292FModel No.: TD-16G40G-20-292F is a high speed threshold detector designed to operate over the 16 to 40 GHz frequency range, with an adjustable threshold level of -20 to 0 dBm, and VSWR of 2.5:1maximum.

Read More

Phase Shifter: PS -360-2433D5-6-SFF-1

May 03, 2012

PS-360-2433D5-6-SFF-1PMI Model No. PS-360-2433D5-6-SFF-1 is a 2433.5MHz ±1MHz, 6-BIT digitally controlled phase shifter that offers up to 360 degrees of phase shift range with a phase accuracy of ±8 degrees typical. This model has a LSB of 5.6 degrees and a low insertion loss of 5 dB typically.

Read More

Band Reject Filter: BR1050-300-CD-TNC-MF

April 27, 2012

BR1050-300-CD-TNC-MFPMI Model No. BR1050-300-CD-TNC-MF is a band reject filter that offers a pass band of DC to 18.0 GHz having 50 dB of rejection from 900 to 1200 MHz. This filter has only 1.5 dB of loss and a VSWR of 2.0:1 maximum. This filter can handle input power levels up to 5 W.

Read More

Double Throw Switch: PEC-9R510R7-100W-SFF-SPDT

April 27, 2012

PEC-9R510R7-100W-SFF-SPDTPMI Model No.PEC-9R510R7-100W-SFF-SPDT is a high power, single pole, double throw switch capable of handling 120 W CW. This solid-state switch operates in the frequency range of 9.5 to 10.7 GHz and has a typical insertion loss of 1.5 dB and port to port isolation of over 40 dB.

Read More

Filter Bank: 7SFB-950M18G-CD-SFF

April 27, 2012

7SFB-950M18G-CD-SFPMI Model 7SFB-950M18G-CD-SFF is an eight channel switched filter bank that covers pass-band frequencies of 950 MHz to 18.05 GHz. This filter bank offers 7 different pass-bands throughout the operating frequency which can be selected via a 3-bit decoded TTL signal.

Read More

Solid State Absorptive Switch: P4T-0R1G20G-100-T-SFF

April 24, 2012

Switch-P4T-0R1..PMI Model P4T-0R1G20G-100-T-SFF is a single pole, four throw, solid-state absorptive switch which operates over the 100 MHz to 20.0 GHz frequency range. This model provides 110 dB of isolation over the entire frequency range of operation and offers low insertion loss performance with fast switching speeds.

Read More

Bi-Phase Modulator: BPM-1G2G-1-SFF

April 17, 2012

BPM-1G2G-1-SFFModel BPM-1G2G-1-SFF is a bi-phase modulator designed to operate over the 1.0 to 2.0 GHz frequency range. This model can handle RF input signal levels up to -3 dBm and has an insertion loss of 8.8 dB maximum.

Read More

Low-Noise Amplifier: PE2-4020-9R510R7-2R5-12-12-SFF-VVG

April 17, 2012

PE2-4020-9R510R7-2R5-12-12-SFF-VVGPMI Model No. PE2-4020-9R510R7-2R5-12-12-SFF-VVG is a voltage variable gain, low-noise amplifier that operates over the 9.5 to 10.7 GHz frequency range. This model provides 40 dB of small signal gain with a typical noise figure of 4.0 dB and an OP1dB of +12 dBm.

Read More

Threshold Detector: TD-30T-218-FC-HS Option 220

April 17, 2012

TD-30T-218-FC-HS OPTION 220Model TD-30T-218-FC-HS Option 220 is a high speed threshold detector designed to operate over the 2 to 20 GHz frequency range. It has as external adjustment to vary the threshold level from -10 to -20 dBm, with an input flatness of typically ±1.0 dB and a VSWR of less than 3.0:1.

Read More

Switch: P2T-500M20G-50-T-512-SFF-I-NH

April 16, 2012

P2T-500M20G-50-T-512-SFF-I-NHPMI Model No. P2T-500M20G-50-T-512-SFF-I-NH is a terminated single pole, two throw switch that operates from 500 MHz to 20 GHz which handles +23 dBm CW input power. The port to port isolation is 50 dB minimum, Insertion loss of 2.8 dB maximum and has a maximum switching speed of 50 nsec.

Read More

Single Sideband Modulator: PSM-50M1G-CD-1

April 12, 2012

PSM-50M1G-CD-1PMI Model PSM-50M1G-CD-1 is a single sideband modulator that operates over the 50 MHz to 1.0 GHz frequency range. The input P1dB is +5 dBm typical and has an IF Modulation Range of DC to 10 MHz. The IF Modulation Power Range is +7 dBm minimum and +13 dBm maximum into 50 ohms.

Read More

Portable Amplifier: PTB-42-1G40G-12-292FF-DC12

March 28, 2012

AmpPTB-42-1G40G-PMI Model PTB-42-1G40G-12-292FF-DC12 is a portable amplifier that operates over the 1.0 to 40.0GHz frequency range. This model provides 40dB of typical gain with an OP1dB of +22dBm typical (1-18GHz) and +18dBm typical (18-40GHz).

Read More

Pin Diode Attenuator: PVVAN-0R4G6G-40-MP-1

March 14, 2012

AttenuatorPVVAN-0R4G6G-PMI Model Number PVVAN-0R4G6G-40-MP-1 is a non-reflective, linearized, voltage controlled pin diode attenuator. This model operates over the 400 MHz to 6.0 GHz frequency range and provides up to 40 dB of attenuation range from 0 to +10 VDC control voltage. Typical insertion loss is 2.8 dB with a typical speed of 1 usec.

Read More

Phase Shifter: PS-360-2D4G2D5G-10-CD-SFF

March 05, 2012

PhaseShifterPS3602D4G2PMI Model Number PS-360-2D4G2D5G-10-CD-SFF is a 2.4 GHz to 2.5 GHz, 10-Bit digitally controlled phase shifter that offers up to 360 degrees of phase shift range. This model has a LSB of 0.36 degrees and a low insertion loss of 4.0 dB typically.

Read More

Diode Attenuator: DTA-100M40G-30-CD-1

February 16, 2012

AttenuatorDTA-100M40GPMI Model Number DTA-100M40G-30-CD-1 is a 5-Bit, digitally controlled 30 dB PIN diode attenuator with a step resolution of 1 dB covering the frequency range of 100 MHz to 40 GHz. This model operates on +5 VDC and only draws 40 mA. Attenuation accuracy of 0.6 dB is achieved due to PMI's proprietary digital calibration techniques.

Read More

Amplifier: PTB-40-0R118-6R5-21-120VAC-1U-SFF

February 09, 2012

PTB-40-pmi100PMI Model number PTB-40-0R118-6R5-21-120VAC-1U-SFF is an integrated microwave assembly that provides high gain and operates from 100 MHz to 18 GHz.  This unit features integrated digitally controlled attenuators with ranges up to 60 dB.  The attenuation can be controlled via the external optical encoded knob or via RS-232 and Ethernet.

Read More

SPDT Switch: P2T-1G18G-10-R-528-SFF-HIP10W

January 31, 2012

PMIswitch100PMI Model P2T-1G18G-10-R-528-SFF-HIP10W is a 1.0 to 18.0GHz, solid-state SPDT switch that can handle up to 10 W CW of input power for all operating conditions.

Read More

0.4 GHz TO 16 GHz 2 WAY POWER DIVIDER

January 17, 2011

PlanarAPD-2-0416-YR1_pic1smallPlanar Monolithics Industries Inc. is pleased to announce the development of it’s new 0.4 to 16 GHz 2 way power divider, model number: APD-2-0416-YR1. The insertion loss from 0.4 to 6 GHz and 6 to 16 GHz are 1.8 dB max and 4.0 dB max, respectively.

Read More

0.5 GHz TO 18 GHz 2 WAY POWER DIVIDER

January 17, 2011

PlanarAPD-2-0518-YR1_picsmallPlanar Monolithics Idustries Inc. is pleased to announce the development of it’s new 0.5 to 18 GHz 2 way power divider, model number: APD-2-0518-YR1. The insertion loss and isolation from 0.5 to 8 GHz and 8 to 18 GHz are 1.8 dB max, 16.5 dB min and 3.5 dB max, 21 dB min, respectively.

Read More

1.3 TO 1.7 Ghz ADJUSTABLE THRESHOLD DETECTOR LOG AMPLIFIER

January 17, 2011
PLANAR MONOLITHICS INDUSTRIES, INC. has developed the PMI Model No: TA-SDLVA-0120-70 OPTION 105F ADJUSTABLE THRESHOLD DETECTOR LOG AMPLIFIER that operate from 1.3 to 1.7 Ghz (other frequencies are available), and are designed using cutting edge GaAs technology which provides stunning performance and reliability in a compact package. Read More

140 MHz, ±25MHz, Amplifier Detector Preamp

January 17, 2011

ADP140M51DRtdPlanar Monolithics Industries offers the Detection Preamp Module, Model Number ADP-140M-51DR-TD with Options HS, NRL, LOG, which Provides Amplification, Video Detection, and Video Amplification with an Input of 130 MHz Pulsed RF with a 25 MHz Bandwidth.The Size is 3.50”(L) X 3.00”(W) X 0.50”(H).

Read More

2 MHz to 18 GHz, Ultra-Broadband, Threshold Detector

January 17, 2011

Planar2CDT-2M18-30-BB-DE-D_picPlanar Monolithics Industries, Inc. (PMI) is very proud to announce the development of an Ultra-Broadband Threshold Detector which operates from 2 MHz to 18.0 GHz. The VSWR is 1.9:1 Max. and the Thru Path Insertion Loss is 2.5dB Max. The Dynamic Range is -30 to 0 dBm with a 10kHz Video Bandwidth.

Read More

2.0 to 18.0 GHz, 65dB, Direction Finding Receiver Frontend

January 17, 2011

AmMicRFE-218-70-BB-JT_picturesmallPlanar Monolithics Industries, Inc is pleased to offer our latest development: Model RFE-218-70-BB which is a 2.0 to 18.0 GHz direction finding receiver frontend.The minimum dynamic range of the subsystem is -60 to +5 dBm; while the Input VSWR in frequency range is 3.0:1 and the frequency flatness at the outputs is ±3.0 dB maximum.

Read More

4 TO 8 GHz TRUE HIGH SPEED COMPACT SDLVA

January 17, 2011

PlanarMSDLVA-2020-70-48-SEsmallPLANAR MONOLITHICS INDUSTRIES, INC. has developed the PMI Model No: MSDLVA-2020-70 OPTIONS 48 & SE SDLVA’S that operate from 4 to 8 Ghz (other frequencies are available). This unit has high speed and uses GaAs technology in a compact size. The dynamic range is 80 dB. The VSWR is 1.6:1 typical. The TSS is -73 dBm typical.

Read More

8 GHz TO 11 GHz 10 dB Directional Coupler

January 17, 2011

RFOC-811-QRC-DC-10Planar Monolithics Industries Inc. is pleased to announce the development of it’s new 8 to 11GHz 10 dB directional coupler with field replaceable SMA connectors, model number: RFOC-811-QRC-dc-10. By using the technology of microstrip line to strip line transitions, all the feed thrust of input and output ports can be soldered directly to the mechanical housing to have better mechanical support.

Read More

8 GHz TO 11 GHz RF SIGNAL PROCESSING ASSEMBLY

January 17, 2011

Planar2RFOC-811-QRC_picPLANAR MONOLITHICS INDUSTRIES, INC. is pleased to announce the development of it’s new 8 to 11GHz RF signal processing assembly, model number: RFOC-811-QRC. The assembly includes three independent sub-systems. Totally 29 RF components are integrated in the assembly.

Read More

8-BIT DIGITAL CONTROLLED PHASE SHIFTER

January 17, 2011

PlanarPS360sPMI Model Number PS-360-DC-3, Option 618 is a 6 to 18 GHz, 0 to 360˚, 8 Bit Digitally Controlled Phase Shifter with a Switching Speed of less than 50 nS, Rise and Fall time of less than 20 nS. Insertion Loss of 10 dB typical, 12 dB maximum, VSWR of 2.0:1 and with a Phase Accuracy of ±12˚ p-p maximum from 8 to 18 GHz and ±15˚ p-p maximum from 6 to 18 GHz.

Read More

Amplifier: Model ERDLVA-218-CW-LPD

January 17, 2011

ERDLVA-218-CW-LPD100PMI Model ERDLVA-218-CW-LPD is a CW Immune, Extended Range Detector Logarithmic Video Amplifier (ERDLVA) designed for ultra low DC power consumption. This model operates over the 2 to 18 GHz frequency range and has the ability to interface with an output cable measuring over 100 feet in length.

Read More

Digital Phase Shifter, PS-360-3237-5-292FF

January 17, 2011

68-100Model Number PS-360-3237-5-292FF is a 32 to 37 GHz Digitally Controlled Phase Shifter with Capability for Phase Shifting from 0 to 349°. 5 Logic Lines allow various phase shift with a LSB of 11.25°.

Read More

Digitally Tuned Oscillators

January 17, 2011

pmi100PMI would like to announce its newest product line addition of digitally tuned oscillators (DTO). They now offer a full line of digitally tuned oscillators (DTO) covering various frequencies in the 500 MHz to 18 GHz range.

Read More

High Speed Phase Shifter

January 17, 2011

PlanarPS-90-8018-812-HS15NS_picsmallPlanar Monolithics Industries Model No: PS-90-8018 Option 812, HS15NS is a high speed 0 to 180 degree, miniature, bi-phase modulator / phase shifter with TTL control logic (ECL logic available). This high speed model has 15 nS delay on/off and operates between 8 to 12 GHz.

Read More

HIGH SPEED THRESHOLD DETECTOR

January 17, 2011

PlanarTD-30T-914-DX_pic1smallPlanar Monolithics Industries Model No: TD-30T-914-DX is a High Speed Threshold Detector Designed to Operate over the 9 to 14 GHz Frequency Range, with an Adjustable Threshold Level of -18 dBm to +5 dBm, and a Typical VSWR of 2.0:1 (2.5:1 Maximum).

Read More

LM-35D5G-14-20W-292FF High Power Limiter

January 17, 2011

65-100Model LM-35D5G-14-20W-292FF is a high power limiter capable of withstanding an input power level of 20 W, 440 to 670 nsec Pulse Width, PRF 600 to 900kHz, 40% Duty Cycle. This model operates in the 35 to 36GHz frequency range, but can be used over the 24.5 to 38GHz frequency range with degraded performance. The insertion loss is 3.0 dB maximum, VSWR of 2.0:1 and 250 nsec response time packaged in a small 0.50 X 0.50 X 0.22 housing.

Read More

MINIATURE 2.0 TO 18.0 GHz POWER DIVIDER

January 17, 2011

PlanarAPD-2-218-M-BB_picsmallPlanar Monolithics Industries, Inc. (PMI) is very proud to offer our Model ADP-2-218-M-BB Miniature Power Divider.This Power Divider is designed to operate from 2.0 to 18.0 GHz, with an Insertion Loss of only 2.2dB Maximum, Isolation of 16.0 dB Minimum and a VSWR of 2.0:1 Maximum.

Read More

MINIATURE, 2 TO 18GHz THRESHOLD DETECTOR

January 17, 2011

PlanarTD-30T-218-FC-HS_pic1smallPMI Model No: TD-30T-218-FC-HS is a Threshold Detector with Hybrid MIC/MMIC Technology which operates over the full 2.0 to 18.0 GHz frequency range (other frequency ranges also available).The device is high speed with a response time of #100 nS and a minimum dynamic range of -20 dBm to -10 dBm (with -20 dBm to +5 dBm typical).

Read More

P1T-18G40G-90-1515-292FF Solid-State Switch

January 17, 2011

60-100PMI Model No. P1T-18G40G-90-1515-292FF is a solid-state single pole, single throw switch that operates over the 18.0 to 40.0GHz frequency range. This model offers ULTRA-HIGH Isolation measuring greater than 90 dB while maintaining a low insertion loss of 5.0 dB maximum.

Read More

P4T-500M40G-60-T-55-292FF

January 17, 2011

SP4T_100PMI would like to announce its newest solid-state switch that offers a level of performance exceeding industry standards. PMI Model No. P4T-500M40G-60-T-55-292FF is an absorptive, solid-state switch that covers the 500 MHz to 40 GHz frequency range. This model offers extremely low insertion loss, very high isolation and a typical switching speed of 27 nsec.

Read More

PEC-2D35G-100W-SFF-SPDT Solid-State Switch

January 17, 2011

19-100PMI Model No. PEC-2D35G-100W-SFF-SPDT is a solid-state switch capable of hot switching over 100 W of input power. Most high power switches are not of a solid-state design and do not offer the benefit of fast switching speeds. PMI has developed a unique design that offers fast switching speeds as well as the added reliability of solid-state devices.

Read More

PEC-42-1G40G-20-12-292MM Low Noise Amplifier

January 17, 2011

LNA-PEC-42PMI Amplifier Model PEC-42-1G40G-20-12-292MM is an ultra-broadband, low noise amplifier that covers the 1.0 to 40.0 GHz frequency range. This model provides a flat gain response while maintaining a typical output power of +20 dBm. [Other specifications available upon request.]

Read More

PMI Model P16T-0R5G18G-60-T-SFF Switch

January 17, 2011

SFFswitch-P16TPMI would like to announce its newest solid-state switch that offers a level of performance exceeding industry standards. PMI Model No. P16T-0R5G18G-60-T-SFF is an absorptive, solid-state switch that covers the 500 MHz to 18 GHz frequency range.

Read More

PS-360-3237-5-292FF Phase Shifter

January 17, 2011

PhaseShifter-PS-360Model Number PS-360-3237-5-292FF is a 32.0 to 37.0GHz Digitally Controlled Phase Shifter with Capability for Phase Shifting from 0 to 349˚.  5 Logic Lines allow various phase shift with a LSB of 11.25˚.

Read More

Quadrature Hybrid

January 17, 2011

QC-052-YR3The model QC-052-YR3 is a 3 dB quadrature hybrid that when a signal is applied to any port the hybrid will split that signal equally between the ports on the side away from the input with the port adjacent to and on the same side as the input port remaining isolated.

Read More

Radar/Microwave Monitoring Receiver

January 17, 2011

RMR-818-77-NRLThe model RMR-818-77-NRL is an 8 to 18 GHz radar/microwave monitoring receiver de-signed for laboratory applications. The receiver uses an extended range detector log video amplifier (DLVA), a pre-amplifier and RF bandpass filtering. It also offers a dynamic range of 75 dB with a typical TSS of -80 dBm.

Read More

SDLVA-218-71-70MV Log Video Amplifier

January 17, 2011

SDLVA-218...LogVideoAmpPMI Model SDLVA-218-71-70MV is a CW Immune, Extended Range Detection Log Video Amplifier (ERDLVA) which offers 71 dB dynamic range over the frequency range of 2.0 to 18.0 GHz. This model offers a maximum rise time of 35 nsec and a recovery time of less than 350 nsec. CW immunity is provided for signal levels up to -40 dBm.

Read More

SDLVA-218-71-70MV ERDLV Amplifier

January 17, 2011

SDLVA-218...ERDLVampPMI Model SDLVA-218-71-70MV is a CW Immune, Extended Range Detection Log Video Amplifier (ERDLVA) which offers 71 dB Dynamic Range over the frequency range of 2.0 to 18.0 GHz. This model offers a maximum rise time of 35 nsec and a recovery time of less than 350 nsec.

Read More

SDLVA-6G18G-CD-1 SDLV Amplifiers

January 17, 2011

SDLVA-6G18GModel SDLVA-6G18G-CD-1 Successive Detection Log Video Amplifiers (SDLVA) offers 75 dB Dynamic Range over the frequency range of 6.0 to 18.0GHz. This model offers an ultra-fast rise time of 10nsec maximum and a recovery time of less than 60nsec. The unit is temperature compensated such that log linearity over temperature remains less than +/-2.5dB.

Read More

Solid-State Switch - Model No. P2T-100M1G-90-T-55-SFF

January 17, 2011

SSS-P2T-100MPMI would like to announce its newest solid-state switch that offers a level of performance exceeding industry standards. PMI Model No. P2T-100M1G-90-T-55-SFF is an absorptive, SP2T solid-state switch that covers the 100MHz to 1.0GHz frequency range. This model offers extremely low insertion loss, very high isolation and a switching speed of 50nsec maximum.

Read More

Solid-State Switch - Model No. P2T-8G11G-90-T-SFF

January 17, 2011

SSS-SP2T100PMI would like to announce its newest solid-state switch that offers a level of performance exceeding industry standards. PMI Model No. P2T-8G11G-90-T-SFF is an absorptive, SP2T solid-state switch that covers the 8.0GHz to 11.0GHz frequency range. This model offers extremely low insertion loss, very high isolation and a switching speed of 50nsec maximum.

Read More

Solid-State Switch - Model No. P5T-100M1G-90-T-55-SFF

January 17, 2011

SSS-P5T100PMI would like to announce its newest solid-state switch that offers a level of performance exceeding industry standards. PMI Model No. P5T-100M1G-90-T-55-SFF is an absorptive, SP5T solid-state switch that covers the 100MHz to 1.0GHz frequency range. This model offers extremely low insertion loss with very high isolation.

Read More

Solid-State Switch: P2T-18G40G-65-R-292FF

January 17, 2011

P2T-18G40G-65-R-292FFPMI Model P2T-18G40G-65-R-292FF is a single pole, two throw, solid-state switch which operates over the 18 to 40 GHz frequency range. This model provides 55 dB of isolation over the entire frequency range of operation and offers low insertion loss performance with fast switching speeds.

Read More

Solid-State Switch: Model No. P8T-0R1G20G-110-T-512-SFF

January 17, 2011

SolidStateSwitch100

PMI Model No. P8T-0R1G20G-110-T-512-SFF is a high speed, single pole, eight throw, absorptive switch capable of switching within 300 nsec.  The frequency range is 0.1 to 20.0 GHz and has over 110 dB of isolation.

Read More

Solid-State Switch: P4T-0R1G20G-100-T-SFF

January 17, 2011

SolidStateSwitch100PMI Model P4T-0R1G20G-100-T-SFF is a single pole, four throw, solid-tate absorptive switch that operates over the 100 MHz to 20 GHz frequency range. This model provides 110 dB of isolation over the entire frequency range of operation and offers low insertion loss performance with fast switching speeds.

Read More

Successive Detection Log Video Amplifier (SDLVA)

January 17, 2011

PlanarSDLVA-61F-80-5829387-004-TBRK-MSsmallPlanar Monolithics Industries Model No: SDLVA-61F-80-582987-004 Option TBRK, MS is a matched set of successive detection log video amplifiers in a compact stacked configuration. This unit operates over 61.25 MHz ± 250 KHz with a transfer function of E – 22.5 PIN+ 200, where PIN is the input power in dB above -80 dBm and E = output voltage in millivolts.

Read More

Temperature Compensated, Limiting Amplifier: PEC3-40-2G6G-15LM-SFF-HS

January 17, 2011

TempCompAmp100Model PEC3-40-2G6G-15LM-SFF-HS is a temperature compensated, limiting amplifier that operates over the 1.85 to 6.25 GHz frequency range and provides a limited power output of +15 dBm minimum for an input power range of -15 to +17 dBm.

Read More

Threshold Detector/Coupler/Switch

January 17, 2011

tdcsThe model TDCS-4T-10F-HP is an integrated threshold detector, 17 dB coupler and SPDT PIN diode switch. This device operates from 9 to 10.5 GHz (other frequency ranges are also available), with an insertion loss of 2 dB maximum, VSWR of 1.5 maximum, 2 W average RF input power handling capability and TTL threshold output.

Read More

Two-Way Power Divider

January 17, 2011

RFOC-811-QRC-2-PDThe model RFOC-811-QRC-2-PD is a 6 to 13 GHz two-way power divider. The insertion loss from 6 to 12 GHz and 12 to 13 GHz are 0.6 dB maximum and 0.9 dB maximum, respectively. The isolation in the entire frequency range is 18 dB minimum.

Read More

ULTRA HIGH SPEED, HIGH SENSITIVITY THRESHOLD DETECTOR

January 17, 2011

ThresholdDetector100Planar Monolithics Industries, Inc. has developed the PMI Model No.: TD-30T-SHS-218-30DBAMP Options DAC, DS, an Ultra-High Speed, High Sensitivity Threshold Detector designed for Broad Band Applications in the 2 to 18 GHz Frequency Range and with an 8 Bit Digital Control.

Read More

News

Planar Monolithics Industries Inc.'s PTRAN-100M18G-SFB-3UVPX-MAH transceiver

June 03, 2014

PMI Model No. PTRAN-100M18G-SFB-3UVPX-MAH is a transceiver covering the frequency range of 100MHz to 18GHz. The transceiver fits into a 3U Open VPX from factor utilizing the high speed VITA 67 RF Connector.  This unit up-converts a 100MHz to 4GHz transmit signal to the 2.0 to 18.0GHz range. 

Read More

PMI acquires HARI LLC

May 15, 2013

Planar Monolithics Industries Inc. (PMI) has announced that effective April 30 2013, PMI acquired100% of all the assets & property of Hari LLC

Read More

PMI and AMC head in new, separate directions

May 14, 2013

Raymond Sicotte, chairman and CEO of American Microwave Corp. (AMC), and Ashok (Ash) Gorwara, chairman, president and CEO of Planar Monolithics Industries Inc. (PMI), wish to announce that they have completed realignment and separation of AMC and PMI.

Read More

PMI to exhibit at IMS 2012

June 06, 2012

Join PMI in Montréal, Canada to experience a record breaking year for the IEEE IMS. Celebrating the 60th anniversary of the MTT-S and featuring the theme Microwave Without Borders, the IMS 2012 will be the centerpiece of Microwave Week June 17-22, 2012. PMI has broken many records in the history of the symposium such as the number of paper submissions and the number of advanced bookings by exhibitors. Read More

PMI introduces solid-state SPDT switch

January 30, 2012
Planar Monolithics Industries Inc.'s (PMI) Model P2T-1G18G-10-R-528-SFF-HIP10W is a 1.0 to 18.0 GHz, solid-state SPDT switch that can handle up to 10 WCW of input power for all operating conditions. Read More

PMI Releases New Product Line

August 31, 2011
PMI is announcing its newest product line addition of Digitally Tuned Oscillators (DTOs). PMI now offers a full line of digitally tuned oscillators (DTOs) covering various frequencies in the 500 MHz to 18 GHz range. All models are designed to withstand stringent military ground or airborne environments. These models... Read More

PMI and AmpliTech Join Forces

April 16, 2010
Planar Monolithics Industries (PMI) and AmpliTech are excited to announce the collaboration of their combined product offering, engineering skills and marketing efforts. AmpliTech is the vendor of choice for numerous Tier 1 and Tier 2 mil/space concerns requiring a wide variety of complex amplifiers with mission-critical specifications. PMI has... Read More

PMI and Amplitech Announce Collaborative Agreement

January 14, 2010
Planar Monolithics Industries and Amplitech announced the collaboration of their combined product offering, engineering skills and marketing efforts. The companies will independently run the administrative and production facilities but will share a combined manufacturer's representative sales force, marketing effort and will direct future engineering requirements to the facility best... Read More

Planar Monolithics Industries (PMI) announces its merger with Planar Electronics Technology (PET) and Planar Filter Company (PFC)

February 05, 2008
The synergy between these three Frederick, Maryland based corporations enables the offering of upgraded Hybrid MIC/MMIC RF and Microwave Components, Subsystems, and Systems to their customers as well as enhancing their ability to support major military and defense contractors. Read More

Articles

USB Style RF/Microwave Components

September 14, 2012

Planar Monolithics Industries (PMI) has developed a family of USB controlled RF and microwave components including amplifiers, switches and attenuators.

Read More

Your request will be e-mailed directly to the company who will follow up with the requested information. This request is for legitimate sales inquires only – please do not submit promotions, solicitations or spam.

Back to Listings

Sign-In

Forgot your password?

No Account? Sign Up!

Get access to premium content and e-newsletters by registering on the web site.  You can also subscribe to Microwave Journal magazine.

Sign-Up

advertisment Advertisement